manualshive.com logo in svg

Honeywell WV8840B, Installation Instructions Manual, Page: 8 / 8

Share
Download
Honeywell WV8840B Installation Instructions Manual Download Page 8

WV8840B WATER HEATER CONTROLS

Automation and Control Solutions

Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN  55422
customer.honeywell.com

® U.S. Registered Trademark
© 2013 Honeywell International Inc.
69-2450—03    M.S.  Rev. 11-13
Printed in United States

IMPORTANT

Follow the operating instructions provided by 

the manufacturer of your water tank appliance. 

The information in this form describes a typical 

water heater control application, but the specific 

controls used and the procedures outlined by 

the manufacturer of your appliance can differ, 

requiring special instructions.

STOP: READ THE 

WARNINGS ABOVE.

If the appliance does not turn on when the setpoint knob 

is set several degrees above the previous temperature, 

follow these instructions:

1.

Set the temperature setpoint knob to OFF.

2.

Turn off the main gas valve to the appliance.

3.

Wait five minutes to clear out any unburned gas. If 

you then smell gas, STOP! Follow step 1 in the 

warning above. If you DO NOT smell gas, continue 

with the next step. 

4.

Turn on the gas supply to the appliance.

5.

Restart the appliance by performing lighting 

procedure.

6.

Set the setpoint knob to the desired setting.

7.

If the appliance does not turn on, turn off the gas 

supply to the appliance and contact a qualified 

service technician for assistance.

TURNING OFF THE 

APPLIANCE

Complete Shutdown

1.

Turn device knob to OFF. Turn off the gas supply to 

the appliance. Appliance will completely shut off. 

2.

Follow the procedure in the Instructions to the 

Homeowner section above to resume normal 

operation.

Summary of Contents for WV8840B









Reviews:

No comments