manualshive.com logo in svg

Honeywell VX3Plus, Reference Manual, Page: 197 / 282

Share
Download
Honeywell VX3Plus Reference Manual Download Page 197

User Interface

The Enabler can be configured and controlled manually through the user interface on the VX3Plus. This section details the
functionality that can be controlled by the user or system administrator.

Parameters and Screen Displays

Screen displays shown in this section are designed to present the end-user with information graphically.

Placement of information on the screen displays may be split between one or many tabbed panels.

Standard Avalanche Enabler parameters that are not supported by Honeywell may be missing or dimmed (visible but unable to
be edited) on the tabbed panels or screen displays.

Enabler Configuration

Depending on the version of the Enabler running on the VX3Plus, the desktop Enabler icon may look like one of the following:

The available configuration options and tabs may vary by Enabler version. The examples shown in this section assume the
latest version of the Enabler is installed on the VX3Plus.

The Enabler user interface application is launched by clicking either the

Enabler icon

on the desktop or Taskbar or by

selecting

Avalanche Enabler

from the Programs menu.

The opening screen presents the VX3Plus user with the connection status and a navigation menu.

Note:

Some parameters and features described in this section may not be available if you are not running

the latest version of the Enabler. Contact your

representative

for upgrades.

4-7

Summary of Contents for VX3Plus



























































































































































































































































































Reviews:

No comments