Honeywell VR8215N Installation Instructions Manual Download Page 1

INSTALLATION INSTRUCTIONS

69-2253-07

VR8215S,T Single Stage
VR8215Q,N Two Stage
Direct Ignition Gas Controls

APPLICATION

The VR8215S,T Single Stage and VR8215Q,N Two 
Stage Direct Ignition Gas Controls are used in gas-
fired appliances with up to 150 ft

3

/hr capacity at 1 in. 

wc pressure drop on natural gas. They have been 
optimized for direct ignition applications and include 
a on/off switch and a pressure regulator.

• Valve capacities are shown in Table 1.
• Table 2 provides gas capacity conversion factors.
• For suffix letter designation, see Table 3.

Table 1.  Valve Capacity.

a

a

Capacity based on 1000 Btu/ft

3

, 0.64 sp gr natural gas at 1 in. wc pressure drop (37.3 MJ/m

3

, 0.64 sp gr 

natural gas at 0.25 kPa pressure drop).

b

Minimum regulation for LP gas is 30,000 Btu/h (0.85 m

3

/hr).

Table 2. Gas Capacity Conversion Factor.

Table 3. Model Number Suffix Letter Designation.

Options:

3/16 in. (4.8 mm) and 1/4 in. (6.4 mm) male quick-

connect ground terminals.

Barbed vent fittings for seated combustion: 

Single stage: 1/8 in. (3.2 mm) and 1/4 in. (6.4 mm)
Two stage: 1/4 in. (6.4 mm)

SPECIFICATIONS

Body Pattern: 

Straight through; see Table 1 for inlet  

and outlet size.

Electrical Ratings:

Voltage and Frequency: 24 Vac, 50/60 Hz.
Current Draw: 

Single Stage: 0.5 A. 
Two Stage: 0.9 A.

Field Wiring:

Single Stage: Two 1/4 in. spade quick-connect terminals.
Two Stage: Molex and spade quick-connect terminals 

(two 1/4 in. and one 3/16 in.).

Capacity: 

See Table 1.

Conversion:

Use conversion factors in Table 2 to convert 

capacities for other gases.

Regulation Range: 

See Table 6.

Natural-LP Gas Conversion Kits: 

See Table 4.

Approvals:

CSA Design Certificate #112395. 

(-40 °F to +175 °F; -40 °C to +79 °C)

Australian Gas Association Certificate #7960. 

(single stage only)  (-20 °C to +79 °C only)

Outlet: 

Class 2, Grade 20 pressure regulator

Auto shutoff valve function: 

Class 3

Model

Size

Inlet x 
Outlet 

(in. NPT)

AGA Certified Capacity 

for Natural Gas

AGA Certified 

Minimum Regulation 

for  Natural Gas

AGA Certified 

Maximum Regulation 

for Natural Gas

ft

3

/hr

m

3

/hr

ft

3

/hr

m

3

/hr

ft

3

/hr

m

3

/hr

VR8215

1/2 x 1/2

150

4.25

15

b

0.42

200

5.66

Gas

Specific Gravity

Multiply Listed 

Capacity By

Manufactured

0.60

0.516

Mixed

0.70

0.765

Propane

1.53

1.62

Regulation

Model Number 

Suffix Letter

Pressure 

Regulator Type

Single Stage

S

Standard

T

Slow  Opening

Two Stage

Q

Standard

N

Slow  Opening

Summary of Contents for VR8215N













Reviews: