Honeywell VR4300 Manual Download Page 1

TABLE 2—ADAPTER (FLANGE) PART NUMBERS.

Part Number

Inlet/

Without

With

Outlet

Flange

Hex

Hex

Pipe Size

Type

Wrench

Wrench

1/2 inch NPT

Straight

393690-6

393690-16

Elbow

393690-3

393690-13

3/4 inch NPT

Straight

393690-4

393690-14

Elbow

393690-5

393690-15

NOTE: Flange kits include one flange with attached O-ring

and fan mounting screw.

TABLE 3—GAS CAPACITY CONVERSION

FACTORS.

Specific

Multiply Listed

Gas

Gravity

Capacity By

Manufactured

0.60

0.516

Mixed

0.70

0.765

Propane

1.53

1.62

APPROVALS:

American Gas Association design certificate: UP-70-57A.
Canadian Gas Association design certificate: 1029-CC-8375.

 T.H.  •  Rev. 3-93  •  © Honeywell Inc. 1993  •  Form Number 69-0683—1

TABLE 1—TEMPERATURE RANGES AND

REGULATOR TYPES.

Ambient

Model

Temperature

Regulator

Number

Range

Type

VR4300A

0

°

 F to 175

°

 F

Standard-opening

[-18

°

 C to +79

°

 C]

VR4300C

0

°

 F to 175

°

 F

Step-opening

[-18

°

 C to +79

°

 C]

VR4300H

0

°

 F to 175

°

 F

Slow-opening

[-18

°

 C to +79

°

 C]

VR4300M

-40

°

 F to 175

°

 F

Standard-opening

[-40

°

 C to +79

°

 C]

VR4300P

-40

°

 F to 175

°

 F

Step-opening

[-40

°

 C to +79

°

 C]

VR4300

Continuous Pilot

Combination Gas Control

Application

These continuous pilot gas controls are used in gas-fired

appliances with capacities up to 300 feet

3

/hour at one inch wc

pressure drop [5.7 meters

3

/hour at 0.25 kPa] on natural gas.

They include a manual valve, safety shutoff, two automatic
operators, a pressure regulator, pilot adjustment, and a con-
duit cover. See Table 1 for temperature ranges and regulator
types.
BODY PATTERN: Straight-through body pattern.

INLET X OUTLET SIZES AVAILABLE: 1/2  by 3/4 inch

and 3/4 by 3/4 inch.

ADAPTERS: Adapters available for 1/2 and 3/4 inch straight

and angle connections. Refer to Table 2.

ELECTRICAL RATINGS:

Voltage and Frequency: 120 Vac, 60 Hz.
Current Draw: 0.14A.
Use conversion factors in Table 3 to convert capacities for

other gases.

CAPACITY:

Inlet x Outlet

Capacity at 1 inch wc

Minimum

Maximum

Size (In.)

Pressure Drop

a

Regulated Capacity

Regulated Capacity

1/2 X 1/2

180 feet

3

/hour

30 feet

3

/hour

225 feet

3

/hour

[5.1 meter

3

/hour]

[0.8 meter

3

/hour]

[6.4 meter

3

/hour]

1/2 X 3/4

190 feet

3

/hour

30 feet

3

/hour

290 feet

3

/hour

[5.4 meter

3

/hour]

[0.8 meter3/hour]

[8.2 meter

3

/hour]

3/4 X 3/4

200 feet

3

/hour

30 feet

3

/hour

300 feet

3

/hour

[5.7 meter

3

/hour]

[0.8 meter

3

/hour]

[8.5 meter

3

/hour]

a

Capacity based on 1000 Btu/feet

3

, 0.64 specific gravity natural gas at 1 inch wc pressure drop [37.3 MJ/meter

3

, 0.64 specific

gravity natural gas at 0.25 kPa pressure drop].

Summary of Contents for VR4300











Reviews: