manualshive.com logo in svg

Honeywell Thor VM3, User Manual, Page: 61 / 378

Share
Download
Honeywell Thor VM3 User Manual Download Page 61

Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide

49

Display

The display is a thin-film transistor display capable of supporting SXGA graphics 
modes. Display size is 1024x768 pixels. The display covering is designed to resist 
stains. The display supports screen blanking to eliminate driver distraction when the 
vehicle is in motion. 

Touch Screen

The touch screen is a Resistive Panel with a scratch resistant finish that can detect 
touches by a stylus, and translate them into computer commands. In effect, it simulates 
a computer mouse. Only Delrin or plastic styluses should be used. A right mouse click is 
simulated by touching and holding the screen for the appropriate time interval. 

When a dialog box is too large for the display, tap and drag the dialog box up or down or 
from side to side to view the remainder of the dialog box.

Always use the point of the stylus for tapping or making strokes on the display. Never 
use an actual pen, pencil, sharp or abrasive object to write on the touch screen. 

An extra or replacement stylus may be ordered. 

A replaceable touch screen protective film is available when the Thor VM3 is used in an 
abrasive environment. Contact 

Technical Assistance

 for availability.

Note:

If the touch screen is disabled or loses calibration on a Thor VM3, you must use a USB 
mouse or keyboard attached to the Thor VM3 to access the control panel to re-enable or 
recalibrate the touch screen unless a programmable key has been assigned to that 
function.

Touch Screen Defroster

Extended temperature versions of the Thor VM3 contain a touch screen defroster. The 
touch screen defroster can be disabled when not needed via the 

Peripherals

 control 

panel. The defroster trip point is configurable. The defroster is always disabled when the 
device is operating from UPS battery power.

Screen Blanking

Screen blanking (blackout) can be enabled when the vehicle is in motion. See 

Screen 

Blanking

 for hardware setup and 

Screen Control

 for software setup to enable screen 

blanking. Once screen blanking is enabled, the display is blanked out any time when the 
cable sends the signal that the vehicle is in motion. If the cable is removed, screen 
blanking is disabled and the display remains on.

Summary of Contents for Thor VM3



























































































































































































































































































































































































Reviews:

No comments