background image

1

68-0148—1

 B.M.  •  Rev. 6-94  •  ©Honeywell Inc. 1994  •  Form Number 68-0148—1

T8131A,B,C; T8132A,B,C

Programmable Thermostats

The T8131 and T8132 Thermostats provide

energy savings for single-stage heating and cool-
ing applications while providing reliable, precise
temperature control.

T8131/T8132 Models

HEAT-OFF-COOL system switch.

AUTO-ON fan switch.

Separate programs for weekdays and weekends
5 day/2 day.

Digital LCD display.

Easy to program and install.

Precise temperature control.

Four daily energy saving programs.

Available in taupe and Premier White

.

Compatible with most 24 Vac standing pilot, gas
electronic ignition, oil or central electric systems.

T8131 Models Only

Powered directly from 24 Vac system transformer.

Green light emitting diode (LED) lights when prop-
erly connected.

Two AA alkaline batteries for backup power
recommended.

T8132 Models Only

Requires two AA alkaline batteries.

LCD flashes “bAt Lo” indicating low battery power.

Isolated heating/cooling circuits.

T8131C
T8132C

CONTENTS

Specifications ................................................ 2
Ordering Information .................................... 2
Installation .................................................... 3
Programming the Thermostat ....................... 8
Checkout and Settings ................................. 10
Troubleshooting .......................................... 11
Cross Reference .......................................... 12

Summary of Contents for T812A1002 - Mechanical Thermostat













Reviews: