background image

INSTALLATION INSTRUCTIONS

62-0310-01

Spyder

®

 BACnet

®

Programmable, VAV/Unitary Controllers

 

PRODUCT DESCRIPTION

The PUB6438S, PVB6436AS and PVB6438NS controllers are 

part of the Spyder family. The three controllers are BACnet 

MS/TP network devices designed to control HVAC equipment. 

These controllers provide many options and advanced system 

features that allow state-of-the-art commercial building 

control. Each controller is programmable and configurable 

through software.

These controllers are for use in VAV (Variable Air Volume) and 

Unitary HVAC control applications. Each controller contains a 

host micro controller to run the main HVAC application and a 

second micro controller for BACnet MS/TP network 

communications. Each controller has flexible, universal inputs 

for external sensors, digital inputs, and a combination of 

analog and digital Triac outputs. The three models are 

described in Table 1. The photo to the left is the model 

PVB6436AS, which includes the actuator.

Table 1. Controller configurations.

Each controller communicates via an EIA-485 BACnet MS/TP network communications network, capable of baud rates between 

9.6 and 115.2 kilobits.
Controllers are field-mountable to either a panel or a DIN rail. 

SPECIFICATIONS

General Specifications

Rated Voltage:

 20–30 Vac; 50/60 Hz

Power Consumption:

 

100 VA for controller and all connected loads (including the 

actuator on model PVB6436AS).

Controller Only Load: 

5 VA maximum; models PUB6438S 

and PVB6438NS.

Controller and Actuator Load:

 9 VA maximum; model 

PVB6436AS.

External Sensors Power Output:

 20 Vdc ±10% @ 75 mA 

maximum.

VAV Operating & Storage Temperature Ambient Rating 

(models PVB6436AS and PVB6438NS):

Minimum 32 ºF (0 ºC); Maximum 122 ºF (50 ºC)

Unitary Operating & Storage Temperature Ambient Rating 

(model PUB6438S):

Minimum -40 ºF (-40 ºC); Maximum 150 ºF (65.5 ºC)

Relative Humidity:

 5% to 95% non-condensing

LED: 

Provides status for normal operation, controller down-

load process, alarms, manual mode, and error conditions

BEFORE INSTALLATION

The controller is available in three models (see Table 1).

Controller

Model

Programmable

Type

Universal

Inputs

(UI)

Digital

Inputs

(DI)

Analog

Outputs

(AO)

Digital

Outputs

(DO)

Velocity

Pressure

Sensor

(Microbridge)

Series 60

Floating

Actuator

PUB6438S

Unitary

6

4

3

8

NO

NO

PVB6436AS

VAV

6

4

3

6

YES

YES

PVB6438NS

VAV

6

4

3

8

YES

NO

Summary of Contents for Spyder PUB6438S









Reviews: