background image

EC AP MKT

Page 13

Confidential and Proprietary

Configuration & Operation

Item

Operation

Display

Proportional
Band Setting

• Press “SELECT” to choose “P BAND”.
• Press key 

S

1 time “ST” will be 1

0

C up. The range is 2-19

0

C. Hold the key 2 seconds up; the temperature 

increases continuously until reaches 19

0

C. Press the button again, temperature change stops.

• Press key 

T

1 time “ST” will be 1

0

C down. The range is 19-2

0

C. Hold it 2 seconds up, the temperature 

decreases continuously until reaches 2

0

C. Press the button again, temperature change stops.

• Press, “ENTER” button to save setting value.

Offset Setting

• Press “SELECT” to choose “OFFSET”.
• Press key 

S

1 time “ST” will be 0.5c up; the range is from –3 to 3

0

C. Hold the key in 2 seconds; the 

temperature increases continuously until reaches 3

0

C. Press the button again, temperature change stops.

• Press key 

T

1 time, “ST” will be 0.5

0

C down; the range is from 3 to-3

0

C. Hold the key in 2 seconds, the 

temperature decreases continuously until reaches –3

0

C. Press the button again, temperature change stops.

• Press, “ENTER” button to save setting value.

Mode Setting

• Press “SELECT” to choose “MODE”.
• Press key 

S

1 time “ST” will be 1 up, the range is 0-6

0: output1—cooling  output2--no function

1: output1--heating  output2--no function

2: output1—cooling  output2--heating

3: output1--heating  output2--cooling

4: output1—cooling   output2--low temperature limit

5: output1--heating  output2--high 

temperature limit

• When the value reaches 5, the setting value will not change.
• Press key 

T

1 time “ST” will be 1 down until to 0, then no change if continue to press the key.

• Press, “ENTER” button to save setting value.

Sensor
Setting

• Press “SELECT” to choose “SENSOR”.
• Press key 

S

“ST”, the value switches between 0 and 1: 0

Æ

internal sensor

1

Æ

external sensor

• Press key 

T

“ST”, the value switches between 1 and 0

• Press, “ENTER” button to save setting value.

Summary of Contents for Smartronic70 T9275A1002





















Reviews: