manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 422 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 422

1126800 

SmartPAC 2 with WPC Integration

Page 400

Chapter 7

SmartPAC 2 Fault Messages

Customized Status Codes

DANGER

!

USER INPUTS 1 THROUGH 7 ARE NOT CONTROL RELIABLE

Do not use inputs 1 through 7 as part of any personnel protection system.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

USER INPUTS 8 THROUGH 11 ARE CONTROL RELIABLE ONLY IF CORRECTLY
WIRED IN PAIRS

Wire and use input pairs 8 & 9 and 10 & 11 as instructed in this document.

Failure to comply with these instructions will result in death or serious injury.

NOTICE

You can display the status of the user interlocks from Initialization  mode.  See “Using the
WPC Input Status Display,” page 420.

50  through  58

Problem:

These error codes indicate failures that have occurred to auxiliary
equipment that you connected to WPC, such as lubrication systems.
Codes 50 and 58 are related to the cross-checked user input pairs (see
table, below, and also refer to codes 17 and 18, which are also related to
the user inputs).  For more information about the user inputs, see pages 52
in the Installation chapter and page 225 in the Initialization chapter.

Remedy:

Check the auxiliary equipment that signaled the stop (see "Wiring WPC
User Inputs," page 52 in Chapter 2).  Correct the problem.  Reset
SmartPAC.  If the error does not go away, contact Wintriss Tech Support.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments