Honeywell SmartPAC 2 User Manual Download Page 247

Page: 247 / 522

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Initialization Mode

Chapter 4

page 225

PRESS CONTROL

[INITIALIZATION – PRESS CONTROL]

Figure 4 - 22. Press Control Initialization Mode

The WPC Initialization menu enables you to perform the following procedures:

•

Set up the user interlocks, “User Interlocks,” next section

•

Set press parameters, “Press Parameters,” page 229

•

Set press option switches, “Press Options,” page 241

•

Check input status, see “Using the WPC Input Status Display” in Chapter 7, page
420.

User Interlocks

[INITIALIZATION – PRESS CONTROL – USER INTERLOCKS]

DANGER

USER INPUTS 1 THROUGH 7 ARE NOT CONTROL RELIABLE

Do not use inputs 1 through 7 as part of any personnel protection system.

Failure to comply with these instructions will result in death or serious injury.

DANGER

USER INPUTS PAIRS 8 & 9 AND 10 & 11 ARE CONTROL RELIABLE ONLY IF
CORRECTLY WIRED

Wire and use input pairs 8 & 9 and 10 & 11 as instructed in this manual.

Failure to comply with these instructions will result in death or serious injury.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartPAC 2

Reviews:

Honeywell SmartPAC 2, User Manual, Page: 247 / 522

Search results

Summary of Contents for SmartPAC 2

Reviews: