manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 391 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 391

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Run Mode

Chapter 6

page 369

One-hand Operation, Single Stroke Mode

DANGER

!

IMPROPER SAFEGUARDING

Ensure that the machine guarding system is installed and maintained according to OSHA
standard 1910.217, ANSI B11.1, ANSI B11.19 and any other regulations and standards that
apply.  Ensure that guarding is properly installed to prevent access to the machine over,
under or around any guarding device.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

 INCORRECT INSTALLATION

Shadow light curtains must be properly installed and connected to WPC in order to use ONE
HAND or FOOT modes.

Failure to comply with these instructions will result in death or serious injury.

First, select ONE HAND in the mode select menu (page 365) and turn the stroke select key
to .  To initiate a stroke, press the left RUN/INCH button.  (The left RUN/INCH button must
be used, unless the operator station has an optional right/left hand selector switch.)

You can release that switch at any time, and the ram will complete the stroke.  The ram, how-
ever, will stop if a system fault is detected or if the light curtain is blocked during the down
stroke.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments