manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 387 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 387

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Run Mode

Chapter 6

page 365

Mode Select Menu

These choices
appear only if they
have been enabled
in SmartPAC 2
Initialization

These choices appear only when

Shadow light curtain is configured with

WPC and the appropriate optional

firmware is installed.

F1

F2

F3

F4

F5

F6

F7

F8

Figure 6 - 33.  Mode Select Menu

Your menu may look different

When SmartPAC 2 is in Run mode and the Stroke Select switch is in the OFF position, this
menu appears on the display.  Depending on which options you have, in this menu you can
do the following.  Some items require optional firmware or hardware:

•

Enable Micro-inch

•

Select one of these operating modes:
Two-hand
One-hand or Foot (require Shadow light curtain.  The light curtain will be muted on
the upstroke 

only

 

if WPC has the muting option.)

   

To use the Mode Select menu:
1. Make sure that SmartPAC 2's "Program/Run" key is set to the "RUN" position, and set

the Stroke Select Switch to the "OFF" position.  You will see the Mode Select menu,
above.

2. Use the appropriate function key to select ONE HAND or TWO HAND. Instructions for

each setting are explained below.

3. Next, set the Stroke Select Switch at SmartPAC 2 to the desired operating mode.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments