manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 376 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 376

1126800 

SmartPAC 2 with WPC Integration

Page 354

Chapter 6

SmartPAC 2 Run Mode

ARE YOU LOCKED OUT?

Access to changing the information on this screen may be limited to Program mode or may
require a password.  The security access settings in the Initialization menu determine when
changes can be made.  See “Security Access” in Chapter 4, page 251.

3. Use the cursor keys to increase or decrease the value one digit at a time.
4. Press RESET to set the value and activate the change.
5. If you want to adjust the other items, select the desired item from the Press control

display (Figure 6 - 20), then repeat steps 2 through 5. (You cannot adjust "Main air.”)

6. Press RESET to exit from this screen and return to the main Run menu.

Show Overrun Angles

Wintriss Tech Support may ask you to check the overrun sensor ON and OFF angles.

To do this, go to Run mode, and select Press Control (see previous section).  Press 

F3-

“Show

Overrun Angles.”  A box appears in the center of the display, similar to Figure 6 - 21.

F1

F2

F3

F4

F5

F6

F7

F8

Figure 6 - 21.  Show Overrun Angles

(RUN – PRESS CONTROL – 

F3-

SHOW OVERRUN ANGLES)

Viewing Actual Counterbalance and Main Air Pressure Limits

(Optional)

From the screen where you were just making adjustments ("Press Control," Figure 6 - 20),
you can also view your press's actual counterbalance and main system air pressure limits.
Keep in mind that if you did not set limits for counterbalance and clutch air in SmartPAC 2's
Initialization, these values will not be displayed in Adjust mode.  

Note:  You cannot make

changes to these values.

   Again press RESET to exit from this screen and return to the first

Run menu.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments