manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 297 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 297

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Program Mode

Chapter 5

page 275

Entering and Exiting Program Mode

To Enter Program Mode

To Exit Program Mode

From Run mode:

Turn the Program/Run key toward PROG.*
_________________________

From Initialization mode:

Go to the top Initialization menu.
Press RESET.

—or—

Turn the Program/Run key to RUN and then
back to PROG.*

To go to Run mode:

Turn the Program/Run key toward RUN.*
_________________________

To go to Initialization mode:

Press the “1” and “CLEAR” keys
simultaneously and hold down a few seconds
until the Main Initialization menu appears.

*  If you turn the key and nothing happens, press RESET repeatedly until the SmartPAC 2 changes

modes.  To prevent this problem, before you turn the Program/Run key, make sure SmartPAC 2 is in
the main (or top) menu for the mode it is in. If it is not, press RESET repeatedly until the main menu
appears.

If “PRESS CONTROL IS IN LOCKOUT MODE” appears on the display, turn the stroke
select key to OFF and then back to the desired operating mode to clear the message.

NOTICE

Refer to Chapter 3 for instructions on using the keyboard on SmartPAC 2.  See Figure 3 - 21
on page 193 in that chapter for an example of how to move through the menus in Program
mode.

NOTICE

SELECT = HIG ENTER

When this manual says “select,” it means highlight the item and press ENTER.

For information on the menu items in the main Program menu see the following:

TOOL MANAGER, next section

SENSOR ENABLE/DISABLE & STATUS, page 317
RECALCULATE SETPOINTS, page 319

For HELP press the HELP key located at the center of the cursor (arrow) keys.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments