manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 339 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 339

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Program Mode

Chapter 5

page 317

SENSOR ENABLE/DISABLE & STATUS

[PROG - SENSOR ENABLE/DISABLE & STATUS]

In the main Program menu, select SENSOR ENABLE/DISABLE & STATUS.  A screen
appears similar to the following figure.

F1

F2

F3

F4

F5

F6

F7

F8

Figure 5 - 41.  Sensor ON/OFF Status

If you have DiProPAC, this screen lists the die protection sensors and their status, OFF, ON
or N/U (not used).  If you have ProPAC process monitor, this screen lists the process monitor
sensors.  The screen shows sensors 1 – 8.  If you have sixteen-sensor options, press 

F4

-“Next

8 Sensors” to see the other eight sensors.  To get back to the first eight, press 

F4

 again.

NOTICE

When a tool is loaded, or when SmartPAC 2 is powered up, all sensors are turned ON and
enabled.

Controlling Which Sensors SmartPAC 2 Monitors

There are three ways to control which sensors SmartPAC 2 monitors. You can enable or
disable all sensors, turn an individual sensor off or on, and delete a sensor. Follow these
instructions to perform these operations:

•

Enable or Disable All Sensors, next section

•

Turn a Sensor OFF or ON, page 318

•

Delete a Sensor, page 301

For HELP press the HELP key located at the center of the cursor (arrow) keys.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments