manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 255 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 255

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Initialization Mode

Chapter 4

page 233

WPC INITIALIZATION MENU

USE THE CURSOR KEYS 

USER INTERLOCKS

TO SELECT THE ITEM  

PRESS PARAMETERS

YOU WISH TO SEE. 

 

PRESS OPTIONS

PRESS ENTER TO  

 

INPUT STATUS

ACCESS  IT. PRESS
RESET WHEN DONE.

USER INTERLOCKS

Figure 4 - 28.  WPC Initialization Menu

3.

 

Select “Press Parameters."  The Press Control Parameter menu appears (next figure). Use
the cursor keys to highlight "Stop Limit" in the display shown below.  Then press
ENTER to select.

TOP STOP DEFLT
CARRYUP ANGLE
MICRO TIME
MICRO ANGLE
MAIN AIR LIMIT
CNTR BAL +/-
STOP LIMIT
START LIMIT
SHUT DOWN LIMIT
FLYWHEEL TIMER
ACTS ANGLE

220 DEG
149 DEG

100 MSEC

185 DEG

0 PSI
0 PSI

250 MSEC
199 MSEC

5  MIN

6 SEC

0  DEG

=
=
=
=
=
=
=
=
=
=
=

                  INITIALIZE PARAMETERS

USE THE CURSOR KEYS TO CHOOSE THE VALUE
YOU WANT TO CHANGE.
PRESS THE ENTER KEY TO CHANGE THE VALUE.
PRESS THE RESET KEY WHEN DONE.

PRESS CONTROL PARAMETER MENU

250

Figure 4 - 29.  "Press Parameters" Display in SmartPAC's Initialization Mode

4.

 

The bar highlights the Stop Time Limit value.  To change this value, press ENTER.  Now
the message at the bottom of the display reads

5.

 

Use the number keys to change the Stop Time Limit.  Press ENTER to accept the change.
Use the cursor key to select the Start Time Limit value.  Do as you did in step 2 for start
time limit.  Press RESET when done.  The WPC Initialization menu appears.

6.

 

Select "Press Control.”  The WPC Initialization menu appears. Select “Press Options.”
In the menu that appears, set Switch 7 to CLOSED to disable changes (see page 247).

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments