manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 269 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 269

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Initialization Mode

Chapter 4

page 247

Switch 7 –Disable Changes to Stop Time Limit and Auto Carry-up Angle

NOTICE

After you change switch settings, power down the SmartPAC 2/WPC. Power it up again to
enable the new settings. If you do not this, the previous switch settings will remain in effect.

With this switch OPEN, you can change the settings for Stop Time Limit and Auto Carry-up
Angle. When this switch is set to CLOSED, you cannot change these settings.

Table 4 - 10.  Switch 7 Setting to Enable/Disable Changes to Stop Time Limit

and Auto Carry-up Angle

Option Switch 7 Setting

Changes to

Stop Time Limit and Auto Carry-up Angle

OPEN

Enabled

CLOSED

Disabled

NOTICE

CHANGE FROM PREVIOUS VERSIONS OF WPC:  TOP STOP IN INCH DISABLED WITH
INPUT PIN 13

To disable top stop in inch, connect on the WPC processor board, connect Pin # 13 to
+24 VDC.  (Previous versions used Switch 7)

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments