manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 211 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 211

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Keyboard, Displays

Chapter 3

 Page 189

and Operating Modes

Table 3 - 1.  Initialization, Program and Run Modes

Mode

How to Go to This Mode

How to Exit This Mode

Initialization

Make settings that affect the
operation of SmartPAC 2 with
any and all tools.

You use Initialization mode
extensively when you install a
new SmartPAC 2 and will use
occasionally after you set up
SmartPAC 2 and the press is
running.

See page 190 and Chapter 4.

White text on dark blue display.

Turn Program/Run key to
PROG.*  Then press the “1”
and “CLEAR” keys
simultaneously and hold down a
few seconds until the Main
Initialization menu appears.

To go to Program mode:

Press RESET.

_______________________

To go to Run mode:

Turn the Program/Run key
toward RUN.*

Program

Create, modify and load
individual tools, including
SmartPAC 2 options for each
tool.

See page 192 and Chapter 5.

Black text on green display.

From Run mode:

Turn the Program/Run key
toward PROG.*
_________________________

From Initialization mode:

Go to the main Initialization
menu.
Press RESET.

—or—

Turn the Program/Run key to
RUN and then back to PROG.*

To go to Run mode:

Turn the Program/Run key
toward RUN.*
_________________________

To go to Initialization mode:

Press the “1” and “CLEAR”
keys simultaneously and hold
down a few seconds until the
Main Initialization menu
appears.

Run

Run the press.  In this mode
you can adjust counters, cams,
sensors and other functions
while the press is running.

See page 194 and Chapter 6.

Black text on light blue display.

Turn the Program/Run key
toward RUN.*

To go to Program mode:

Turn the Program/Run key
toward PROG.*

*  If you turn the key and nothing happens, press RESET repeatedly until the SmartPAC 2 changes modes.  To

prevent this problem, before you turn the Program/Run key, make sure SmartPAC 2 is in the main (or top)
menu for the mode it is in. If it is not, press RESET repeatedly until the main menu appears.

   If “PRESS CONTROL IS IN LOCKOUT MODE” appears on the display, turn the stroke select key

to OFF and then back to the desired operating mode to clear the message.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments