manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 216 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 216

1126800 

SmartPAC 2 with WPC Integration

Page 194

Chapter 3

SmartPAC 2 Keyboard, Displays

and Operating Modes

Run Mode

Figure 3 - 22.  Run Mode Main (Top) Menu

When the press is running, SmartPAC 2 should be in Run mode.  The crank angle clock
diagram in the lower left corner of the display shows the rotation of the crankshaft. When the
press is running in continuous mode, the press speed in strokes per minute is displayed in the
center of the clock diagram.  When the press is stopped, or running in inch or single stroke,
the crankshaft angle is displayed.

You may be able to adjust cam timing and perform other operations in Run mode, if allowed
by the security access settings (see “CAM SWITCH (Optional),” page 340).

The figure above shows the main Run menu.  The next figure shows examples of how to
navigate through the SmartPAC 2 menus in Run mode.

See Chapter 6 for detailed instructions on how to use SmartPAC 2 in Run mode.

For HELP press the HELP key located at the center of the cursor (arrow) keys.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments