manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 205 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 205

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Keyboard, Displays

Chapter 3

 Page 183

and Operating Modes

Program/Run Key Switch

ENTER

RESET

PROG

RUN

POWER

BRAKE

WARNING

HELP

1 2 3

4 5 6

9

8

7

.

0

CLEAR

SmartPAC 2

F1

F2

F3

F4

F5

F6

F7

F8

CAMBIE

AL ESPANOL

Program/Run

key switch

PROG

RUN

You use the Program/Run key switch to change between Run and Program modes.  The
switch had a removable key so that access to Program and Run modes can be controlled.

•

When you turn the key toward “Run,” SmartPAC goes into Run mode.

•

When you turn the switch toward “Prog,” it goes into Program mode.

For more information about SmartPAC 2’s operating modes, see “The Three Operating

Modes,” page188 and chapters 4, 5 and 6.

NOTICE

SmartPAC will change from Run to Program or vice versa only when the display shows the
main menu in the mode you are leaving.  If you turn the key and nothing happens, press
RESET repeatedly until you see the new mode appear on the display.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments