Honeywell SmartPAC 2 User Manual Download Page 145

Page: 145 / 522

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 123

Top Stop Angle 301

°°°°

or Greater: Prepare to Install Overrun Sensor Magnet

Go to Initialization mode (page 203). Select PRESS CONTROL. Select PRESS
OPTIONS. On the screen that appears, set Switches 1 and 2 as follows:

Switch 1 – OPEN
Switch 2 – OPEN

To change a switch setting, highlight it and press ENTER to toggle between OPEN and
CLOSED. Press RESET when done.

Power down SmartPAC 2 with WPC and power it up again. This makes the new switch
settings take effect.

Go to Run mode and turn the Stroke Select key to OFF and then back to Inch to clear the
LOCKOUT message (see page 387).

Go to Initialization mode. Select RESOLVER ZERO. On the screen that appears, find
“Current Zero Correction.” Write the Current Zero Correction here:

Go to Table 2 - 15. Find the Current Zero Correction value in the appropriate column in
the table. Circle the “Crankshaft Angle” next to it.

Table 2 - 15. Top Stop Angle 301

°°°°

or Greater: Mounting Overrun Magnet

(Unzeroed Resolver Angle = 359

)

Zero Correction 0

°°°°

- 30

°°°°

Zero Correction 330

°°°°

- 359

°°°°

Current

Zero

Correction

Crankshaft

Angle on

Display

Current

Zero

Correction

Crankshaft

Angle on

Display

Current

Zero

Correction

Crankshaft

Angle on

Display

Current

Zero

Correction

Crankshaft

Angle on

Display

359

344

330

345

358

343

331

346

357

342

332

347

356

341

333

348

355

340

334

349

354

339

335

350

353

338

336

351

352

337

337

352

351

336

338

353

350

335

339

354

349

334

340

355

348

333

341

356

347

332

342

357

346

331

343

358

345

330

344

359

329

Go to Run mode. Turn the Stroke Select key to “Inch.” Inch the press until the
SmartPAC 2 display shows the Crankshaft Angle you circled in Table 2 - 15.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartPAC 2

Reviews:

Honeywell SmartPAC 2, User Manual, Page: 145 / 522

Search results

Summary of Contents for SmartPAC 2

Reviews: