manualshive.com logo in svg

Honeywell Silent knight 5895XL, Installation And Operation Manual, Page: 15 / 48

Share
Download
Honeywell Silent knight 5895XL Installation And Operation Manual Download Page 15

12

5895XL Manual - P/N 151142-L8:L  08/09/2017

Before You Begin Installing

Calculating Current Draw and Standby Battery

1.

The FACP can only support 5 devices w/LED’s on. This current draw has been added to the panels alarm current.

2.

The SK-DUCT housing contains a vacant mount for a SK-RELAY (sold separately). Current draw for the SK-RELAY is calculated by 
increasing the SK-RELAY row of the calculation sheet by one for each SK-RELAY used with a SK-DUCT.

3.

SK-BEAM-T draws a maximum of 500mA from Auxiliary power only when the test feature is used. this should be considered when 
determining auxiliary power capacity but not calculated into current requirements for day to day operation.

4.

If using door holders, you do not need to consider door holder current for alarm/battery standby, because power is removed during that 
time. However, during normal operation, door holders draw current and must be included in the 6.0A total current that can be drawn 
from the panel.

5.

Use next size battery with capacity greater than required.

6.

Total does not include isolator devices or accessory bases.

2.6.3  Current Draw Worksheet for SD SLC Devices

Use Table 2.5 to determine current requirements during alarm/battery standby operation when SD SLC devices are installed.

5

Alarm/Standby:                                 mA

mA

mA

Alarm/Standby:                                 mA

mA

mA

Alarm/Standby:                                 mA

mA

mA

Alarm/Standby:                                 mA

mA

mA

Auxiliary Devices Current

Notification Appliance Circuits

Refer to device manual for current rating.

5495/5499 Power Supply

24 VDC

One input circuit:     15 mA

mA

Both input circuits:   30 mA

mA

Alarm:                                               mA

mA

Alarm:                                               mA

mA

Alarm:                                                mA

mA

Alarm:                                                 mA

mA

Notification Appliances Current

mA

Total current ratings of all devices in system (line A + line B + C)

mA

mA

Total current ratings converted to amperes (line D x .001):

A

A

Number of standby hours:

H

Multiply lines E and F.

Total standby AH

AH

Alarm sounding period in hours. (For example, 5 minutes = .0833 hours)

H

Multiply lines E and H.

Total alarm AH

AH

Add lines G and I.

5

Total ampere hours 
required

AH

Table 2.4   Current Draw Worksheet for SK SLC Devices

Device

# of Devices

Current per Device

Standby 

Current

Alarm 

Current

Table 2.5  Current Draw Worksheet for SD SLC Devices

Device

# of Devices

Current per Device

Standby 

Current

Alarm 

Current

For each device use this formula:      This column      X      This column               =      Current per number of devices.

5895XL Intelligent Power Module 
(Current draw from battery)

1*

Standby                                   40 mA

        40 mA

Alarm:                                          160

 mA

      160 mA

Additional 5895XL
(Daisy-chained to this module)

(7 max.)

Standby                                   10 mA

mA

Alarm:                                            10

 mA

mA

Addressable SLC Devices

SD500-AIM

Standby/Alarm:                          .55 mA

1

mA

mA

SD500-MIM

mA

mA

SD500-PS

mA

mA

SD500-ARM

mA

mA

SD505-HEAT

mA

mA

SD505-PHOTO

mA

mA

Summary of Contents for Silent knight 5895XL

















































Reviews:

No comments