manualshive.com logo in svg

Honeywell Silent knight 5895XL, Installation And Operation Manual, Page: 12 / 48

Share
Download
Honeywell Silent knight 5895XL Installation And Operation Manual Download Page 12

5895XL Manual - P/N 151142-L8:L  08/09/2017

9

Calculating Current Draw and Standby Battery

Before You Begin Installing

2.6  Calculating Current Draw and Standby Battery

This section is for helping you determine the current draw and standby battery needs for your installation.

2.6.1  Worksheet Requirements

The following steps must be taken when determining 5895XL current draw and standby battery requirements.

Filling in the Current Draw Worksheet, Table 2.4 (Section 2.6.2)

1.

For the 5895XL, the worst case current draw is listed for the panel, addressable devices, and SLC expanders. Fill in the number of 
addressable devices and expanders that will be used in the system and compute the current draw requirements for alarm and 
standby. Record this information in Table 2.4 at Line A.

2.

Add up the current draw for all auxiliary devices and record in the table at Line B.

3.

Add up all notification appliance loads and record in the table at Line C.

4.

For notification appliances and auxiliary devices not mentioned in the manual, refer to the device manual for the current ratings.

5.

Make sure that the total alarm current you calculated, including current for the panel itself, does not exceed 6.0 A. This is the 
maximum alarm current allowable.

6.

Complete the remaining instructions in Table 2.4 for determining battery size requirements.

Maximum Battery Standby Load

Table 2.3 shows the maximum battery standby load for the 5895XL based on 24 and 60 hours of standby. The standby load calculations 
of line G in the Current Draw Calculation Worksheet (Table 2.4) must be less than the number shown in Table 2.3 for the battery size 
used and standby hours required.

2.6.2  Current Draw Worksheet

For *each 5895XL in the installation, use Table 2.4 to determine current requirements during alarm battery standby operation when SK 
SLC devices are installed.

6

Table 2.3  : Maximum Battery Standby Load

Rechargeable

Battery Size

Max. Load for 24 hrs. Standby, 

5 mins. Alarm

*Max. Load for 60 hrs. Standby, 

5 mins. Alarm

7 AH

270 mA

105 mA

12 AH

475 mA

190 mA

17 AH

685 mA

270 mA

33 AH

1370 mA

540 mA

*  Required for NFPA 72 Auxiliary Protected Fire Alarm systems for Fire Alarm Service (City Box) and Remote 

Station Protected Fire Alarm systems (Polarity Reversal) and Digital Alarm Communicator/Transmitter (DACT).

NOTE:

33AH max battery size for FM (Factory Mutual) installations

Table 2.4   Current Draw Worksheet for SK SLC Devices

Device

# of Devices

Current per Device

Standby 

Current

Alarm 

Current

For each device use this formula:      This column      X      This column               =      Current per number of devices.

5895XL Intelligent Power Module 
(Current draw from battery)

1*

Standby                                   40 mA

        40 mA

Alarm:                                         

160 mA

         160 mA

Additional 5895XL
(Daisy-chained to this module)

(7 max.)

Standby                                   10 mA

mA

Alarm:                                            

10 mA

mA

Addressable SLC Detectors

SK-PHOTO

Standby/Alarm:                          .30 mA

1

mA

mA

SK-PHOTO-T

mA

mA

SK-HEAT

mA

mA

SK-HEAT-HT

mA

mA

SK-ACCLIMATE

mA

mA

SK-HEAT-ROR

mA

mA

SK-DUCT

2

 (includes PhotoR)

mA

mA

SK-BEAM (without integral test)

SLC

Standby/Alarm:          

2

 mA

Aux. Pwr

Standby:                     

2

 mA

mA

Alarm:                      

8.5

 mA

mA

Summary of Contents for Silent knight 5895XL

















































Reviews:

No comments