manualshive.com logo in svg

Honeywell S89E, Quick Start Manual, Page: 1 / 12

Share
Download
Honeywell S89E Quick Start Manual Download Page 1

PRODUCT DATA

68-0066-4

® U.S. Registered Trademark
Copyright © 2003 Honeywell International Inc.
 All Rights Reserved 

S89E,F

Direct Spark Ignition Control Module

APPLICATION

The Honeywell S89E,F Direct Spark Ignition Control Modules 

control the ignition sequence and gas control operation in 

direct spark systems used primarily on gas-fired atmospheric 

and power burners in residential furnaces and heating 

appliances.

FEATURES

• Requires separate 120 Vac spark generator.
• S89E has 10-second maximum delay for safe start 

check before ignition.

• S89F has 38-second maximum delay for safe start 

check plus valve on delay before ignition.

• Available with 4 or 11 second (nominal) lockout timing.
• 100 percent shutoff for use with all heating gases.
• Ambient temperature rating is -40°F to +175°F (-40°C to 

+80°C).

• Separate electrodes for spark ignition and flame 

sensing.

• Uses Honeywell or any other 2A or less dual valve 

combination gas control designed for Direct Spark 

Ignition (DSI) applications.

• Locks out system after trial for ignition if main burner 

fails to ignite.

• Flame rectification principle used to monitor flame; 

false flame signals resulting from short to ground 

results in safety shutdown.

• After safety shutdown, S89E and F can be reset from 

the thermostat.

Contents

Application ........................................................................

1

Features ...........................................................................

1

Specifications ...................................................................

2

Ordering Information  ........................................................

2

Installation ........................................................................

3

Wiring ...............................................................................

4

Start-Up and Checkout  .....................................................

4

Operation ..........................................................................

6

Troubleshooting ................................................................

7

Summary of Contents for S89E













Reviews:

No comments