manualshive.com logo in svg

Honeywell PRO42R1, Installations And Specifications, Page: 3 / 16

Share
Download
Honeywell PRO42R1 Installations And Specifications Download Page 3

PRO42R1 Installation Guide, Document 800-26500

i

TABLE OF CONTENTS

Chapter 1 - Installation And Specification ..................................................1

General.........................................................................................................................................1
PRO42R1 Hardware ............................................................................................................... 2
Reader wiring............................................................................................................................. 3
Door Strike Relay Wiring ....................................................................................................... 4
Communication Wiring ......................................................................................................... 5
Address Baud Rate and Encryption Configuration Switch ..................................... 6
Status LEDs ...............................................................................................................................7
Specifications............................................................................................................................ 8
Warranty...................................................................................................................................... 9
Liability ........................................................................................................................................ 9

Summary of Contents for PRO42R1

















Reviews:

No comments