Honeywell P531 Page 16 Operating Manual Download

Page: 16 / 27

Page 13

MODELS P531, P532 AND P532UI OPERATING MANUAL

*40056

Channel "A” Primary Read/Write

* 000001 bit 0

* 000002 bit 1

* 000003 bit 2

* 000004 bit 3

* 000005 bit 4 (bit 4 and 5 are viewing head attached

to channel)

* 000006 bit 5 0 ,0 = no viewing head 0,1 = vh #1

….etc.

* 000007 bit 6 IR // for Advanced heads

* 000008 bit 7 UV // for Advanced heads

*40057

Channel "B” Primary Read/Write

* 000001 bit 0

* 000002 bit 1

* 000003 bit 2

* 000004 bit 3

* 000005 bit 4 (bit 4 and 5 are viewing head attached

to channel)

* 000006 bit 5 0 ,0 = no viewing head 0,1 = vh #1

….etc.

* 000007 bit 6 IR // for Advanced heads

* 000008 bit 7 UV // for Advanced heads

*40058

Channel "C" Primary Read/Write

* 000001 bit 0

* 000002 bit 1

* 000003 bit 2

* 000004 bit 3

* 000005 bit 4 (bit 4 and 5 are viewing head attached

to channel)

* 000006 bit 5 0 ,0 = no viewing head 0,1 = vh #1

….etc.

* 000007 bit 6 IR // for Advanced viewing heads

* 000008 bit 7 UV // for Advanced viewing heads

*40059

Pin status R/O

* 000001

* 000002

* 000003

* 000004 bit 3 522 mode pin

PORTC.3

* 000005 bit 4 Channel A Primary = 1 Alt = 0

PORTC.4 (same as 400002 00001)

* 000006 bit 5 Channel B Primary = 1 Alt = 0

PORTC.5

* 000007 bit 6 Channel B Primary = 1 Alt = 0

PORTC.6

* 000008

*40060 SERIAL Number R/O

*40061 ID number READ and WRITE (Signed Integer)

*40062 Operational time each unit = 2 hours of continuous

power on time (R/O)

*40063 Flame On Channel A alternate (0 -> 2999)

*40064 Flame On Channel B alternate (0 -> 2999)

*40065 Flame On Channel C alternate (0 -> 2999)

*40066 Flame Off Channel A alternate (0 -> 2999)

*40067 Flame Off Channel B alternate (0 -> 2999)

*40068 Flame Off Channel C alternate (0 -> 2999)

*40069

Channel "A” Alternate Read/Write

* 000001 bit 0

* 000002 bit 1

* 000003 bit 2

* 000004 bit 3

* 000005 bit 4 (bit 4 and 5 are viewing head attached

to channel)

* 000006 bit 5 0 ,0 = no viewing head 0,1 = vh #1

….etc.

* 000007 bit 6 IR // for Advanced viewing heads

* 000008 bit 7 UV // for Advanced viewing heads

*40070

Channel "B” Alternate Read/Write

* 000001 bit 0

* 000002 bit 1

* 000003 bit 2

* 000004 bit 3

* 000005 bit 4 (bit 4 and 5 are viewing head attached

to channel)

* 000006 bit 5 0 ,0 = no viewing head 0,1 = vh #1

….etc.

* 000007 bit 6 IR // for Advanced viewing heads

* 000008 bit 7 UV // for Advanced viewing heads

*40071

Channel "C" Alternate Read/Write

* 000001 bit 0

* 000002 bit 1

* 000003 bit 2

* 000004 bit 3

* 000005 bit 4 (bit 4 and 5 are viewing head attached

to channel)

* 000006 bit 5 0 ,0 = no viewing head 0,1 = vh #1

….etc.

* 000007 bit 6 IR // for Advanced viewing heads

* 000008 bit 7 UV // for Advanced viewing heads

*40072 Gain Channel A 20ma Gain Alternate (0 – 100 )

*40073 Gain Channel B 20ma Gain Alternate (0 – 100 )

*40074 Gain Channel C 20ma Gain Alternate (0 – 100 )

Alarm set points Alternate

*40075 Alarm set point Channel A (0 -> 2999)

*40076 Alarm set point Channel B (0 -> 2999)

*40077 Alarm set point Channel C (0 -> 2999)

Alarm set points Alternate

*40078 Time Delay (upper nibble Ch B) Lower nibble channel A

(Read change Write)

*40079 FFRT (upper nibble Ch B) Lower nibble channel A(Read

change Write)

*40080 Reserved (do not write to this location) reads zero.

*40081 Time Delay Channel C Alternate

*40082 FFRT Channel C Alternate

*40083

Alternate / Primary Switch register Read/(Write

RS-422 only)

* 000001

* 000002

* 000003

* 000004

* 000005 bit 4 Channel A Primary = 1 Alt = 0

* 000006 bit 5 Channel B Primary = 1 Alt = 0

* 000007 bit 6 Channel B Primary = 1 Alt = 0

* 000008

maxon.su

Summary of Contents for P531




























Search results

Summary of Contents for P531

Reviews:

Related manuals for P531

Brands by name

Popular brands

Honeywell P531, Operating Manual

Search results

Summary of Contents for P531

Reviews:

Related manuals for P531

Brands by name

Popular brands