Honeywell NOTIFIER UDACT-2 Instruction Manual Download Page 38 | Manualshive

Page: 38 / 52

background image

38

UDACT-2 — Instruction Manual

P/N 54089:B3 10/29/2019

Panel-Specific Information

NFS2-640 (UL 864 10th), NFS-320/SYS (UL 864 10th), NFS-640 (UL 8th)

Connect the Ground Wire (PN 71073, provided) from the UDACT-2

EARTH

terminal on TB2 to the CHS-4 Chassis or to a solid building

earth ground.
Connect 24VDC filtered, non-resettable power from the CPU2-640 TB10 to TB1 24V+ and 24V- terminals on the UDACT-2.

To the NFS-640

Connect the communication line between the EIA-485 terminal block TB13 on the CPU2-640 and TB2 terminals EIA-485+ and EIA-

485- on the UDACT-2, being certain to observe polarity.
If the UDACT-2 is the only or last device connected to the EIA-485, set SW1 DIP 1:4 to ON to enable the UDACT-2’s 120 ohm termi-
nating resistor.
Connect the Ground Wire (PN 71073, provided) from the UDACT-2

EARTH

terminal on TB2 to the CHS-4 Chassis or to a solid building

earth ground.
Connect 24VDC filtered, non-resettable power from the CPU2-640 TB7 to TB1 +24V and -24V terminals on the UDACT-2.

Notes

1.

Recommended wire is 12 AWG (3.25mm

2

) to 18 AWG (0.75mm

2

), twisted pair, shielded cable. Connect only one end of shield: a)

shield may be connected to cabinet (earth ground) at fire alarm panel, or b) shield may be connected to TB1 Terminal 5 (Shield) at

UDACT-2 as shown in Figure A.4.

2.

Conduit is required for external wire runs. Consult local building codes.

3.

Refer to "Specifications" on page 8 for power requirements.

Below is a remote installation of a UDACT-2 with an NFS2-640/NFS-320/NFS-320SYS:

NOTE:

The shield end that is not connected should be insulated to prevent accidental grounding. Do not connect both ends of

shield under any circumstance since a ground fault may result.

To Phone Lines
(supervised)

Solid Earth Ground
Connection

NFS2-640/NFS-320/NFS-

320SYS

in Separate Cabinet

ud

act2

-2

64

032

0-

se

pr

tcab

.w

m

f

Wires in conduit

Remote Cabinet

Figure A.4 UDACT-2 and NFS2-640/NFS-320/NFS-320SYS in Separate Cabinets

«
...
36
37
38
39
40
...
»

Summary of Contents for NOTIFIER UDACT-2





















































Reviews:

No comments

Related manuals for NOTIFIER UDACT-2

Brand: Nautel Pages: 23

Brand: Nautel Pages: 66

Brand: National Instruments Pages: 43

Brand: Yaesu Pages: 15

Brand: Audio Precision Pages: 44

Brand: Great Pages: 4

Brand: turck Pages: 8

Brand: American Fibertek Pages: 4

Brand: Lodar Pages: 5

HDMI-GIGALAN-RX

Brand: Spatz Pages: 12

Brand: Airline Pages: 37

ALPHA CON 190 18 DIN CONDUCTIVITY CONTROLLERTRANSMITTER

Brand: EUTECH INSTRUMENTS Pages: 39

Brand: INOR Pages: 2

Brand: Xantrex Pages: 76

Brand: Dini Argeo Pages: 60

Brand: Emcee Pages: 77

Brand: ADEMCO Pages: 4

Brand: Lumel Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands