manualshive.com logo in svg

Honeywell Notifier High-Speed NOTI-FIRE-NET, Instruction Manual, Page: 13 / 18

Share
Download
Honeywell Notifier High-Speed NOTI-FIRE-NET Instruction Manual Download Page 13

High-Speed NFN Manual —

 P/N 54013:C4 8/8/2019

13

Network Wiring for Ground Fault Detection

Network Configurations

•

EXAMPLE 2:

 By setting the ground fault detect switch (SW4) on the repeater to the OFF position, both nodes may provide their 

own ground fault detection (refer to Figure 3.6). The left node provides ground fault detection up to the repeater, and thus must be 
one of the ground fault detection nodes defined on page 12. S2 (Port B) is set to the ON position to enable ground fault detection on 
the left HS-NCM. 
The Port A switch on the right HS-NCM is also set to the ON position, providing ground fault detection up to the repeater. This 
node must also be one of the ground fault detection nodes defined on page 12. 

 

•

 

EXAMPLE 3:

 Ground fault detection is effective for a maximum of two serially connected (point-to-point) repeaters. Therefore, a 

maximum of five HS-NCMs configured as repeaters can be connected in series when ground fault detection is required. Figure 3.7 
shows how the ground fault detection switches must be arranged in order to achieve this maximum configuration.

 

•

EXAMPLE 4:

 The HS-NCM can be shared between two network nodes. In this example, the HS-NCM is shared between two 

nodes with separate power supplies. Ground Fault detection should only be enabled for one of the power supplies.

N

F

NP

TP3P

rv

2.W

M

F

Power Supply 

GF Detect 

Enabled

Power Supply

GF Detect 

Enabled

Twisted-Pair Wire

Twisted-Pair Wire

Ports

Ports

Ports

Network Node

Network Node

OFF

GF Detect 

Enabled

GF Detect 

Enabled

Figure 3.6  Point-to-Point (EXAMPLE 2)

NFNP

TP

4rv3

.WMF

HS-NCM

Node

HS-NCM

Node

HS-NCM 

as a 

repeater

HS-NCM 

as a 

repeater

GF Detect 

Switches 

enabled

Both GF 

Detect 

Switches 

enabled

Both GF 

Detect 

Switches 

enabled

GF Detect 

Switches 

disabled

Figure 3.7  Maximum Point-to-Point Series Repeater 

Ground Fault Pass-Through Configuration (EXAMPLE 3)

Power Supply

GF Detect 

Enabled

Power Supply

GF Detect Dis-

abled

Network Node

Network Node

NFNsh

a

re

HS

NCM

.w

mf

NUP

Port

NUP

Port

NUP

Ports

Figure 3.8  HS-NCM Shared Between Two Network Nodes with Separate Power Supplies (EXAMPLE 4)

Summary of Contents for Notifier High-Speed NOTI-FIRE-NET



















Reviews:

No comments