manualshive.com logo in svg

Honeywell MX8, Reference Manual

Share
Download
Honeywell MX8 Reference Manual Download Page 227

IfTerm

Description

Begins the conditional execution of a block of commands only if the terminal matches the specified terminal type.

Syntax

IfTerm

,

terminal

Parameters

terminal:

The terminal type to determine if the commands should be executed

Example

IfTerm,MX3X

any number of commands

EndIfTerm

Notes

If the terminal type is identical (not case-dependent) the commands are executed.

Nesting with

IfFile

is supported. Nesting with

IfTerm

is meaningless.

Launch

Description

Runs a program.

Syntax

Launch

,

program,wait-code

Parameters

program:

The full path and filename of the program to be run.

wait-code

Tells Launch how to behave when the program is running.

w(ait)

causes Launch to stop processing the script until the program has finished executing.

c(ontinue)

makes Launch continue processing the script while the program is executing.

Example

launch,\Windows\Calc.exe,w

Notes

This differs from

LaunchCmd

in that

Launch

has no parameters.

6-13

Summary of Contents for MX8































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands