Honeywell MeshGuard CO2 IR User Manual Download Page 56

Page: 56 / 59

MeshGuard LEL IR & CO2 IR User’s Guide

Troubleshooting

Failure Symptom

Cause

Solution

Cannot turn on

Battery charge too low

Replace battery

Check RAE Systems

web site for inform-

ation on batteries

OVR (over range)

alarm

Over 100% LEL (LEL

sensor only) or over

the range of the CO

sensor

Condensation inside

Move monitor to a

clean environment

and allow sensor to

clear

Move monitor to a dry

environment, remove

sensor filter, and

allow sensor to dry

out

“

－

0” Alarm

Sensor zero drift

Perform zero

calibration

Controller cannot

receive the MeshGuard

LEL IR’s or MeshGuard

CO2 IR’s signal

Too much distance

between the

MeshGuard LEL IR or

Meshguard CO2 IR

and the controller.

There is an obstruction

between the

instrument and the

controller.

Controller does not

receive completed

data packet

Battery is low

MeshGuard LEL/CO2

IR and controller have

different Pan ID

numbers

The distance should be

300 m, line of sight.

Deploy a router

between the remote

monitor and the

controller.

Relocate the instru-

ment or deploy RTR

mode in instrument or

MeshGuard

Router(s).

Press [Y/+] on the

detector to force it to

send data packets

Replace battery

Set both units to have

the same Pan ID

number

No Antenna Icon

There is no reader or

controller nearby.

The controller or

reader’s network has

changed.

The instrument is out

of its RF range.

Move the instrument

closer to a working

controller or reader.

Perform the network

searching function in

Programming Mode.

Move the instrument

closer to a working

Summary of Contents for MeshGuard CO2 IR




























































Search results

Summary of Contents for MeshGuard CO2 IR

Reviews:

Related manuals for MeshGuard CO2 IR

Brands by name

Popular brands

Honeywell MeshGuard CO2 IR, User Manual

Search results

Summary of Contents for MeshGuard CO2 IR

Reviews:

Related manuals for MeshGuard CO2 IR

Brands by name

Popular brands