www.honeywellvideo.com
+1.800.323.4576 (North America only)
https://honeywellsystems.com/ss/techsupp/index.html
Document 800-12139V1 – Rev B – 05/2013
© 2013 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot
assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change
without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
2 | MAXPRO
®
NVR PE Quick Install Guide
5. Honeywell IP Camera Configuration
Using the MAXPRO NVR Wizard (3 Clicks to Live Video)
The setup wizard starts automatically after you log on (this can take up to
two minutes).
1.
The
CONFIGURATION
dialog appears. When the network is ready
(
or
appears in the notification area), click
to accept
the default settings and proceed to CAMERA DISCOVERY.
To modify the settings for your unique system requirements, refer to
the table below. (After initial setup, you can do this in the MAXPRO
NVR client.)
Click
to reset the values without saving any changes.
2.
The
CAMERA DISCOVERY
window appears. Each newly connected
camera is identified and an IP address is assigned to the camera by
the Wizard, after which the camera reboots.
It may take a few minutes before the cameras are discovered and
added. You will see a
Discovery in progress…
indicator in addition
to a pop-up message on the lower right of your monitor. The list
disappears as the cameras are added to the MAXPRO NVR.
Click
only after all connected cameras are discovered and
added.
Click
to return to the CONFIGURATION page.
3.
The
INSTALLATION
window appears. Click
to start the
MAXPRO NVR application (see 3 Live View).
Note
To add non-Honeywell devices, see
7. Third-Party Device Configuration
.
6. Live View
Log On to the MAXPRO NVR Viewer
1.
When you click
in the Setup Wizard, the
Log On
dialog box
appears. Please wait while the system logs you on automatically as a
Windows Logged-In User.
2.
MAXPRO NVR launches and the Viewer tab appears (see below). The
Devices
area in the left pane lists all of the discovered network
cameras.
View Live Video
To view video from cameras, double-click
MAXPRO NVR
in the
Devices
list
to display video from all discovered cameras in the Viewer. You can also
highlight and drag each camera into a panel.
Note
For continuous monitoring of live video, it is recommended that you use a remote client workstation.
To install a remote client, use the installation software on the software and documentation DVD
included with your unit. Select
Client Installation
as the Installation Type during setup. For more
details, refer to the
MAXPRO
®
NVR Commissioning and Installation Guide
.
Field
Description
Video Format
NTSC, PAL
Start Recording
Start recording as soon as the camera is
added in MAXPRO NVR.
Dynamic IP
Synchronization
NVR synchronizes any change in a
device’s IP address.
Auto Add
Discovered Camera
Any newly connected device is
automatically added to the Devices list.
Choose Camera
Network
Choose your camera’s network.
Auto IP Assignment
Assigns a valid static IP address to the
camera. Use only if you do not have a
DHCP server and you want to assign an
IP address in your computer network
range.
Filter Discovered
Cameras
Filter the discovered cameras based on
the camera model and/or IP range.
STEP 1: CONFIGURATION
STEP 2: CAMERA DISCOVERY
STEP 3: INSTALLATION
Pop-up
message
List of Honeywell IP cameras connected
to and discovered by MAXPRO NVR.
Devices tab: Currently active.
Alarms tab: Acknowledge and clear alarms.
Images/Clips: select images
and clips to view.
Double-click or drag the clip
to a Viewer panel to view.
To export a clip for forensics,
click the arrow
to switch to Full Timeline
mode, then click the
Clip
Export
icon.
Timeline
User currently
logged on
Change
playing speed
Play in
reverse Pause
Play
forward
Select date and time
to start recording
Time jump control to
quickly locate video
Number
of alarms
detected
7. Third-Party Device Configuration
Non-Honeywell devices are configured using the MAXPRO NVR software. To set up cameras for video input:
1.
Launch MAXPRO NVR.
2.
On the
Configurator
tab, click the
Camera
tab.
3.
In the
Discover cameras here
area, click
to discover the
connected cameras in the subnet.
4.
Click
to add the device to the
Camera list and ensure that the
user name and password in the
Advanced Discovery Settings
match the user name and
password of the camera.
5.
To change the default parameters
of a camera, select the camera,
and then click
next to
Launch
Web View For Advanced Set Up
to open the camera advanced
settings pane where you can
modify the settings as required.
6.
Click
Save
for your new settings
to take effect.
Note
For detailed information on adding and configuring third party cameras that do not support automatic discovery,
please refer to the
MAXPRO NVR 2.5 Operator’s Guide
.
8. Advanced Features
Note
For more detailed information on the advanced features available in MAXPRO NVR PE, please refer to the
comprehensive guides available in the UserManuals folder on the software and documentation DVD.
Configurator Tab
Use the
Configurator
tab to configure video devices and set up your MAXPRO NVR PE system. The
Configurator
tab consists of seven sub-tabs:
System
,
Disk
,
Camera
,
Schedule
,
I/O
,
Sequence
,
User
.
Search Tab
Use the
Search
tab to search for recorded video (clips) or events.
1.
Select the check box next to the camera(s) from which the video was recorded.
2.
Select search conditions in the Date time filter, and then click
Search
(
).
9. MAXPRO NVR Default IP Addresses
Your MAXPRO NVR unit has one or two configured network ports with the following default IP addresses:
•
192.168.1.101
for LAN1 (Camera Network)
•
172.25.254.101
for LAN2 (Client Workstation Network) * Not available on some units.
If more than one MAXPRO NVR unit is on the same network, it is recommended that you assign a unique IP address and
computer name to each unit (the default name is
MAXPRO-NVR
).
To change the IP address
1.
Click the network icon (
or
) in the located next to the clock (lower right of screen), click
Open Network and
Sharing Center
, and then click
Change adapter settings
.
2.
Right-click
Camera Network
or
Client Workstation Network
, and then click
Properties
.
3.
Click
Internet Protocol Version 4 (TCP/IPv4)
, and then click
Properties
.
4.
Click
Use the following IP address
, and then, in the
IP address
,
Subnet mask
, and
Default gateway
boxes, type the
IP address settings.
5.
Click
Use the following DNS server addresses
, and then, in the
Preferred DNS server
and
Alternate DNS server
boxes, type the addresses of the primary and secondary DNS servers.
To change the computer name
1.
Click
Start
, right-click
Computer
, click
Properties
, click
Advanced system settings
, click the
Computer Name
tab,
and then click
Change...
2.
Under
Computer name
, delete the old computer name, type a new computer name, and then click
OK
. The name
cannot contain spaces or all numbers or any of the following characters: < > ; : " * + = \ | ?. After changing the
computer name, restart the computer.
3.
Navigate to the C:\Program Files\Honeywell\MaxproNVR\TrinityFramework\bin folder, and then double-click
MaxProNVRMachineNameUtility.exe
to open the Maxpro NVR Utility.
4.
The new computer name should automatically appear in the
Machine Name
field. If it does not, enter the name
manually. Click
Update
. The message
Machine Name Updated Successfully
appears when the update is complete.
More Information
4.
3.
2.
5.
6.
Configurator
tab sub-tabs:
System
: Recording, email, holiday/exceptions for
schedules.
Disk
: Configure and monitor video storage hard drives.
Camera
: Discover and add network cameras, live camera
configuration, recording, video motion detection.
Schedule
: Set recording schedules for recorded video.
I/O
: Configure input and output for each camera.
Sequence
: Select a sequence of cameras for live video.
User
: Set user access and permission levels.
MAXPRO NVR PE
Third Party Devices
Please refer to the appropriate user guide located on the
software/documentation DVD or on the Honeywell
product web site at
www.honeywellvideo.com
.
A comprehensive list of all the third party devices
supported by MAXPRO NVR is available at Honeywell
Open Technology Alliance (HOTA)
www.security.honeywell.com/hota/
.
