2 | MAXPRO
®
NVR XE Quick Install Guide
© 2017 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without
written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However,
Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein
is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
For patent information, see
.
Document 800-16129V4 – Rev A – 03/2017
+1 800 323 4576 (North America only)
https//honeywellsystems.com/ss/techsupp/index.html
+44 (0) 1928 754 028 (Europe only)
https//honeywellsystems.com/ss/techsupp/index.html
Honeywell IP Camera Configuration
Using the MAXPRO NVR Wizard (3 Clicks* to Live Video)
Note
The setup wizard starts automatically but may take two minutes.
Live View
1.
Please wait while the system logs you on
automatically as a Windows Logged-In User.
2.
MAXPRO NVR launches and the Viewer tab
displays (see below).
3.
To view video from cameras, drag
MAXPRO NVR
in the Devices list into the display panel to show
video from all discovered cameras in the Viewer.
You can also highlight and drag each camera into
a panel.
MAXPRO® VIEWER
Multi-site Viewing Software
Honeywell Confidential
& Proprietary
HNMVIEWER
Software
Copyright 2013
Honeywell Inte rnational Inc.
All rights reserved.
1.
The CONFIGURATION dialog appears. When the network is
ready (network icon in Windows tray), click
to accept
the default settings and proceed to CAMERA DISCOVERY.
To modify the settings for your unique system requirements,
follow the table below. After initial setup, you can do this in the
MAXPRO NVR client.
2.
The CAMERA DISCOVERY window appears.
Each newly connected camera is identified and an IP address
is assigned to the camera by the Wizard, after which the
camera reboots. It may take a few minutes before cameras are
discovered and added. You will see a Discovery in progress…
indicator as well as a pop-up message on the lower right of
your monitor. Click
.
3.
The INSTALLATION window appears. Click
to start the
MAXPRO NVR application. Proceed to
4.
Only Honeywell IP cameras and HVE encoders (except
Honeywell Performance Series and New equIP
®
Series IP
cameras) are discovered and added in the MAXPRO NVR
Wizard.
* 3 clicks for specific models with default settings and in a local area
network.
Field
Description
Video Format
NTSC, PAL
Enable Continuous
Recording
Start recording as soon as the camera is
added in MAXPRO NVR.
Dynamic IP
Synchronization
NVR synchronizes any change in a
device’s IP address.
Auto Add
Discovered
Cameras
Any newly connected device is
automatically added to the Devices list.
Choose Camera
Network
Choose your camera network.
Auto IP Assignment
Assigns a valid static IP address to the
camera. Use only if you do not have a
DHCP server and you want to assign an IP
address in your computer network range.
Filter Discovered
Cameras
Filter the discovered cameras based on
the camera model and/or IP range.
Return to
CONFIGURATION
page.
Click only
after all
connected
cameras are
discovered
and added.
Reset values
without saving
changes.
Proceed to
CAMERA
DISCOVERY.
WATCH
User currently logged
on
Number of alarms
detected
List of Honeywell IP devices
and analog cameras
connected to and discovered
by MAXPRO NVR.
Timeline
Change
playing
speed
Play in
reverse
Pause
Play
forward
Select date
and time
to start
recording
Time jump
control to quickly
locate video
Images/Clips:
select images and
clips to view.
Double-click or
drag the clip to a
Viewer panel to
view.
To export a clip for
forensics, click the
arrow
to switch to Full
Timeline mode,
then click the
Clip
Export
icon.
Devices tab: currently active.
Alarms tab: acknowledge and
clear alarms.
Third Party Device Configuration
Additional Configuration
MAXPRO NVR Web Client
To access the Web Client, click on the MAXPRO NVR Web Client shortcut on the NVR desktop. Click
Continue
on the self signed certificate warning message that appears. Login to the Web Client with
default Username:
admin
and Password:
trinity
.
MAXPRO NVR XE Default IP Address Configuration
If more than one MAXPRO NVR XE unit is on the same network, you must assign a unique IP address
and computer name to each unit (the default name is
MAXPRO-NVR
).
1.
To change the IP address using Windows:
a.
Click the
network icon
(
) or (
) located next to the clock (lower right of screen),
click
Open
Network and Sharing Center
, then click
Change adapter settings
.
b.
Right-click
Camera Network
or
Client Workstation Network
, and then select
Properties
.
c.
Click
Internet Protocol Version 4 (TCP/IPv4)
, then click
Properties
.
d.
Click
Use the following IP address
, then in the
IP address
,
Subnet mask
, and
Default gateway
boxes, type the IP address settings.
e.
Click
Use the following DNS server addresses
, and then, in the
Preferred DNS
server
and
Alternate DNS server
boxes, type of the addresses of the primary and
secondary DNS servers. This step is required when clients connect through the
Internet.
2.
To change the computer name using Windows:
a.
Click
Start
, right-click
Computer
, click
Properties
, click
Advanced system settings
,
click the
Computer Name
tab, and then click
Change
.
b.
Under
Computer name
, delete the old computer name, type a new computer name,
and then click
OK
. The name cannot contain spaces or all numbers or any of the
following characters: < > ; : " * + = \ | ?.
c.
After changing the computer name, restart the computer.
d.
Navigate to the C:\Program Files(x86)\Honeywell\MaxproNVR\TrinityFramework\bin
folder, and then double-click
MaxproNVRMachineNameUtility.exe
to open the
MAXPRO NVR Utility.
e.
The new computer name should automatically appear in the Machine Name field. If it
does not, enter the name manually. Click
Update
. The message
Machine Name
Updated successfully
appears when the update is complete.
More Information
1.
On the
Configurator
tab, click the
Camera
tab.
2.
Click
(Auto Discovery) to
automatically discover the connected
IP cameras in the subnet.
3.
Click
(Manual Add) to
manually add the IP device to the
Camera list. Enter the device’s IP
address into the field and ensure that
the user name and password listed for
the new camera match the user name
and password of that camera.
4.
To change the default parameters of a
camera, select it and then click
at
the beginning of the camera line to
open the camera advanced settings
pane where you can modify the
settings as required.
5.
Click
Save
for your new settings to
take effect.
2
1
4
5
3
Use the
Search
tab to search for recorded video (clips) or events.
Use the
Configurator
tab to configure video
devices and set up your MAXPRO NVR
system.
Configurator
tab sub-tabs:
System
: System information, event
recording, email, archival schedule,
holiday/exceptions for schedules.
Disk
: Configure and monitor video
storage hard drives.
Camera
: Discover and add network
cameras, live camera configuration,
recording, video motion detection.
Schedule
: Set recording schedules
configuration.
I/O
: Configure input and output for
each camera.
Sequence
: Select a sequence of
cameras for live video.
User
: Set user access and permission
levels.
Your MAXPRO NVR XE unit has two configured network ports with the following default static IP
addresses:
•
192.168.1.101
for LAN1 (Camera Network)
•
172.25.254.101
for LAN2 (Client Workstation Network)
MAXPRO NVR XE
Third Party Devices
Please refer to the appropriate user
guide located on the software/
documentation DVD or on the
Honeywell product web site at
The
MAXPRO NVR Guides
(Installation and Configuration Guide,
and Operator’s Guide)
provide
detailed information on adding and
configuring third party cameras, the
multi-function Web Client, as well as
other advanced features.
A comprehensive list of all the third
party devices supported by MAXPRO
NVR XE is available on the product
compatibility page:
www.security.honeywell.com/hota/
compatibility/index.html
WATCH
IP