manualshive.com logo in svg

Honeywell MAXPRO NVR Hybrid PE, Hardware Installation And Configuration Manual

Share
Download
Honeywell MAXPRO NVR Hybrid PE Hardware Installation And Configuration Manual Download Page 137

. . . . .

C O N F I G U R I N G   M A X P R O   N V R

Configuring the Cameras

MAXPRO NVR 5.0 Installation and Configuration Guide

137

Adding Additional Streams for a Camera

MAXPRO NVR V4.0 supports adding multiple streams for a single camera. The number of 
streams that can be added depends on the model of the camera. You can also configure each 
stream for a specific device based on your need. For example you can configure the first 
stream for Live recording and the second stream for event based recording. Multistream or 
Dual stream is not supported for encoders.

To configure the additional streams for a camera

1.

Click the 

Camera

 tab, the camera page is displayed with the list of cameras discovered.

2.

For the required camera, click 

 on the left corner, the camera properties pane is 

displayed see 

Figure 6-14

.

Figure 6-14    Camera Properties Pane

3.

Click the 

Add Stream

 button, an additional stream (Stream 2) is added see 

Figure 6-15

.

Summary of Contents for MAXPRO NVR Hybrid PE









































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands