manualshive.com logo in svg

Honeywell MAXPRO NVR Hybrid PE, Hardware Installation And Configuration Manual

Share
Download
Honeywell MAXPRO NVR Hybrid PE Hardware Installation And Configuration Manual Download Page 131

. . . . .

C O N F I G U R I N G   M A X P R O   N V R

Configuring the Cameras

MAXPRO NVR 5.0 Installation and Configuration Guide

131

Configuring the Camera Properties

5.

For the required camera, click 

 on the left corner to open the camera properties pane 

see 

Figure 6-12

.

Figure 6-12    Camera Properties pane

6.

Click 

Launch Camera Web Page

 to launch the web page for the camera. Use the 

camera's web page to view IP and firmware settings, bit rate statistics, camera exposure, 
day night and white balance settings, and set up video motion detection and other 
analytic events.

7.

Under 

General > PTZ > PTZ Settings

•

Device Type

 - Select whether the camera is a PTZ or fixed.

•

PTZ Sensitivity

 - Select the 

PTZ Sensitivity

 for PTZ camera. Available PTZ options 

are: 

Minimum

, 

Low

, 

Normal

, 

High

 and 

Maximum

.

Note:

The 

PTZ Sensitivity

 field is not available for fixed cameras.

8.

Under 

General > 360 Settings

Summary of Contents for MAXPRO NVR Hybrid PE









































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands