Honeywell Maxon CMA11 Instruction Manual Download Page 2

GAS ELECTRO-MECHANICAL VALVES

32M-95001—04

2

E - m - 05/22

WARNING

The installation, operation and maintenance 

instructions contain important information that 

must be read and followed by anyone operating 

or servicing this product. Do not operate or 

service this equipment unless the instructions 

have been read. IMPROPER INSTALLATION OR 

USE OF THIS PRODUCT COULD RESULT IN 

BODILY INJURY OR DEATH.

Description

MAXON electro-mechanical valves are electrically 

actuated fuel shut-off valves. The valves are designed for a 

fast acting return to the at rest position upon removal of a 

control voltage signal. Motorized automatic and manual 

actuators are available depending on application needs. In 

addition, normally-closed and normally-open options are 

available. The normally-closed versions will shut off flow 

when de-energized and pass flow when energized. The 

normally-open versions will shut off flow when energized 

and pass flow when de-energized. Electro-mechanical 

valves are also offered in configurations that meet 

hazardous locations.

Nameplate and abbreviations

Consult the nameplate of your valve. This lists the 

maximum operating pressure, temperature limitations, 

voltage requirements and service conditions of your 

specific valve. Do not exceed nameplate ratings.

Abbreviation or symbol

Description

M.O.P.

Maximum operating pressure

OPENING

Valve opening time (for automatic valves only). Units shown in seconds.

Solenoid/clutch voltage and frequency

Motor voltage and frequency

T

AMB

Ambient temperature range

T

F

Fluid temperature range

SHUT

Visual indication that valve is shut

OPEN

Visual indication that valve is open

SPDT (HS)

Single pole double throw hermetically-sealed switch(es)

SPDT

Single pole double throw switch(es)

SPDT (HC)

Single pole double throw high capacity switch(es) (used when DC motors are 

ordered)

DPDT

Double pole double throw switch(es)

GENERAL PURPOSE AREA Designates components used in general purpose areas

DIVISION 2 AREA

Designates components used in Division 2 hazardous locations areas

Valve is shut

Valve is partially open

Valve is full open

VOS-1/2

Valve open switch(es)

VCS-1/2

Valve closed switch(es); proof of closure

M

Summary of Contents for Maxon CMA11













Reviews: