manualshive.com logo in svg

Honeywell MagicStat CT3300, Installation And Programming Instructions

Share
Download
Honeywell MagicStat CT3300 Installation And Programming Instructions Download Page 3

69-0654-5

INSTALLATION

3

 Step 1. Prepare for installation

a.

Carefully unpack your new thermostat.  Save your receipt and make sure you have the following parts:

b.

Gather the needed tools and supplies listed below.

c.

Make sure that your heating and cooling systems are working properly.  If there is a problem with either system, call a 
heating/air conditioning contractor—the problem may persist after you install the new thermostat.

Required tools and supplies

Optional tools

•

Two AA alkaline batteries.  Honeywell recommends 
Energizer® batteries.

•

Screwdriver

•

Hand or power drill with 3/16-inch or 7/32-inch drill bit

•

Pencil

•

Wire cutter/stripper or sharp knife

•

Level

•

Electrical tape

IMPORTANT: To avoid damaging the compressor in the air conditioner, do not operate the cooling system when the 
temperature outdoors is below 50°F (10°C).

•

Thermostat and mounting plate

•

Labels

•

Screws and anchors

•

Installation and Programming Instructions

Summary of Contents for MagicStat CT3300

























Reviews:

No comments

Brands by name

Popular brands

Load more brands