Resetting the Camera
If setup needs to be repeated, or to connect the camera to a different network, activate the Reset switch as seen at right.
•
To
reset
the connection, press and hold the reset button until the LED on the camera starts blinking white. Release the button
immediately after the LED starts to blink.
•
To
join a new/different
network:
o
On the app’s
Cameras
screen, press
and delete the camera from the link on its
settings
page.
o
Press and hold the
Reset
switch to reset all settings to their factory defaults
o
Unplug the camera and then reconnect it.
o
Repeat the registration procedure.
LED STATUS INDICATOR
During installation
Blue, blinking
Power on. Ready to start setup.
Blue, steady
Connected to the app. Ready to complete setup.
Purple, steady
QR code scan is complete. Restart the Wi-Fi connection process.
Green, blinking
Connecting to Wi-Fi network.
Red, steady
Setup timed out. Unplug the camera, plug it back in and restart setup process.
During operation
Green, blinking
Connecting to Wi-Fi network.
Green, steady
Connected to Wi-Fi and operating.
Note
: The camera is always ready to record but only originates live streaming video when the app
calls for a live stream.
Red, blinking
Not connected to Wi-Fi.
Low-light operation is indicated by four red LEDs arranged around the lens on the front of the camera.
More about mounting at the installation site
IPCAM-WOC1 can be wall- or ceiling-mounted. The camera can be installed with cables running along the outside of a wall, or inside the wall. For outdoor
installations where cables are exposed to the weather, please protect the cable-ends with an enclosure such as a weatherproof single-gang box, available at
most hardware stores. In any installation, make sure the camera’s antenna is firmly connected.
Checking Wi-Fi signal strength at the site using the app:
•
On the
Cameras
page, touch
for
the camera you’re setting up
(on
Android
, touch )
•
Select
Camera Information >
•
Signal Strength
is displayed under
“IP Address”
o
60 – 100 Optimal
o
40 – 59 Marginal
o
0
0
– 39 Use of a Wi-Fi range
extender strongly
recommended
Wall mount example
Ceiling mount example
(both shown with weatherproof single-gang box)
FEDERAL COMMUNICATIONS COMMISSION & ISED STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or
modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may
cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the
specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
If using an indoor antenna, have a quality outdoor antenna installed.
•
Reorient the receiving antenna until interference is reduced or eliminated.
•
Move the radio or television receiver away from the receiver/control.
•
Move the antenna leads away from any wire runs to the receiver/control.
•
Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC / ISED STATEMENT
This device complies with Part 15 of the FCC Rules, and ISED’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’ISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne
doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.
RF EXPOSURE STATEMENT:
The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product procedures.
MISE EN GARDE EXPOSITION AUX FRÉQUENCES RADIO:
La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de séparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas être
située(s) ni fonctionner parallèlement à tout autre transmetteur ou antenne, excepté en conformité avec les procédures de produit multi transmetteur FCC et ISED.
DECLARACIÓN IFETEL
La operación de este equipo está sujeta a las siguientes dos condiciones
1.
Es posible que este equipo o dispositivo no cause interferencia perjudicial y
2.
Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda
causar su operación no deseada.
DECLARACIÓN ANATEL
Este equipamento opera emcarátersecundário, isto é, nãotemdireito a proteção contra
interferência prejudicial, mesmo de estações do mesmotipo, e
nãopodecausarinterferência a sistemas operando emcaráterprimário.
TRADEMARKS
Honeywell is a registered trademark of Honeywell International Inc.
For online support visit, https://mywebtech.honeywell.com/
For the latest warranty information, visit http://www.security.honeywell.com/hsc/resources/wa/
Ê800-23672EŠ
800-23672 9/17 Rev. C
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
2017 Honeywell International Inc.
www.honeywell.com/security