Honeywell HTRD400 Reference Manual Download Page 27

Page: 27 / 176

HTRD400 System Reference Guide

Rev 1.02

Document 900.0328

05/05

Mounting the HTRD400 Recorder

The HTRD400 Recorder is intended for indoor use only. It can be mounted horizontally
(suspend or support mounted) or vertically.

Figure 2-3

shows all the possible ways to

mount the HTRD400 Recorder. Use the two L-brackets supplied with the install kit to mount
it in any of the ways shown.

Figure 2-3

Installation Mounting Options

Prepare the mounting surface. Mark and pre-drill holes for the four #10 x 3/4 inch
sheet metal mounting screws included in the hardware package.

Attach the L-brackets (supplied) to the mounting surface using the sheet metal
mounting screws supplied. If desired, you may also use a suitable substitute.

Secure the HTRD400 Recorder to the two L-brackets with #10-32 x 3/8 inch machine
screws (supplied).

Horizontal mount

Vertical mount

Side mount

Summary of Contents for HTRD400

















































































































































































Search results

Summary of Contents for HTRD400

Reviews:

Honeywell HTRD400, Reference Manual, Page: 27 / 176

Search results

Summary of Contents for HTRD400

Reviews: