manualshive.com logo in svg

Honeywell HON HSV086, Operation & Maintenance Manual, Page: 30 / 48

Share
Download
Honeywell HON HSV086 Operation & Maintenance Manual Download Page 30

 

© 2017 Honeywell International Inc 

Operation and maintenance manual HON HSV086 

  30 

These parts may be ordered as a complete set: 
 

NAME ARTICLE 

NUMBER 

HON HSV086      1" ANSI 300/600 

939403S116970 

                             2" ANSI 300/600 

939403S116980 

                             3" ANSI 300/600 

939403S116990 

                             4" ANSI 300/600 

939403S117000 

                             6" ANSI 300/600 

939403S117010 

                             8" ANSI 300/600 

939403S117020 

                           10" ANSI 300/600 

939403S117030 

                           12" ANSI 300/600 

939403S117040 

HON HSV

S

086  16“ ANSI 300/600 

939403S117050 

HON HSV

S

086  16“ ANSI 900/1500 

939403S206400 

SM 1.x-A 

939405S125370 

SM 2/2500 

939405S189660 

SM90 939405S125360 

 

20" up to 24" on request  

 
Table V: Spare-part sets 

 

 
 

5.7 

Parts list valve and valve body HON HSV 

(see also figure 7a) 
 

PARTS LIST VALVE AND VALVE BODY 

Pos Name 

Pos Name 

01 
02 
03 
04 
05 
06 
07 
09 
10 
11 
12 
13 
14 
15 
16 
17  **  

Filler block 
Retainer set 
Coupling 
Connection rod 
Connection rod guide 
Ring 
Retainer holder 
Top cover 
Locking pin 
Name plate 
Valve 
Retaining plate 
Valve stem 
Valve seat 
Valve body 
By-pass line 
 
 

21  * 
22  * 
23  * 
24 
25 
26  * 
27 
28 
29 
30  * 
31 
32  * 
33 
34 
35 
40 * 

41 * 

O-ring retainer set  (2x) 
O-ring connection rod 
O-ring guide 
Countersunk screw 
Retaining ring 
O-ring top cover 
Plug 
Socket screw 
Compression spring 
O-ring valve 
Countersunk screw 
O-ring valve seat  
Set screw with tap 
Ring 
Collar plug 
O-ring   (only 8“ - 10“ - 12“ ) 

Safety nut  (only 8“ - 10“ - 12“ ) 

 

Table VI: Parts list shut-off device 

 
* 

Recommended spare parts 

** 

Standard, a by-pass line with by-pass valve in the form of a spring closed ball 
valve or a spring-closed push-button valve is supplied. This is used to equalise 
the pressure upstream and downstream of the shut-off valve to open the 
valve. 

Summary of Contents for HON HSV086

















































Reviews:

No comments