manualshive.com logo in svg

Honeywell GSMVLP4G, Installation And Programming Manual, Page: 24 / 24

Share
Download
Honeywell GSMVLP4G Installation And Programming Manual Download Page 24

 

 

 

 

Federal Communications Commission (FCC) Part 15 

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's 

Manual.  Unauthorized changes or modifications could void the user's authority to operate the equipment. 

CLASS B DIGITAL DEVICE STATEMENT 

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC 

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This 

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, 

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 

•

  Reorient or relocate the receiving antenna. 

•

  Increase the separation between the equipment and receiver. 

•

  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

•

  Consult the dealer or an experienced radio/TV technician for help. 

This Class B digital apparatus complies with Canadian ICES-003. 

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

 

FCC IC Statement  

This device complies with Part 15 of FCC Rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference 

that may cause undesired operation. 
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis 

aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interférences nuisibles. (2) Cet appareil doit accepter toute interférence 

reçue y compris les interférences causant une réception indésirable. 

 

 

RF Exposure 

WARNING: 

The antenna(s) used for this transmitter must be installed to provide a separation distance of at 

least 7.8 in (20 cm) from all persons and must not be co-located or operating in conjunction with any other 

transmitter except in accordance with FCC multi-transmitter product procedures. 

Mise en Garde 

Exposition aux Fréquences Radio:

 L'antenne (s) utilisée pour cet émetteur doit être installée à  une 

distance de séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.

 

 

SUPPORT & WARRANTY 

For the latest documentation and online support information, 

please go to: 

https://mywebtech.honeywell.com/ 

 

For the latest warranty information, please go to: 

www.honeywell.com/security/hsc/resources/wa. 

 

 

MyWebTech 

 

Warranty

 

 

 

 

Ê800-12200V2LŠ 

800-12200V2  5/15  Rev A

 

 

Summary of Contents for GSMVLP4G

























Reviews:

No comments