12
LCD-SLP Product Installation Document —
P/N LS10045-000GF-E:E 12/16/2019
3.2.1 LCD-SLP Wired to the S3 Series Panel
Figure 3.2.1.1 illustrates terminal connections of the LCD-SLP touchscreen wired to the S3 Series panel.
Figure 3.2.1.1 LCD-SLP Wired to the S3 Series Panel
3.2.2 LCD-SLP Wired to the E3 Series Panel
Figure 3.2.2.1 illustrates the terminal connections of the LCD-SLP wired to the E3 Series panel.
Figure 3.2.2.1 LCD-SLP Wired to the E3 Series Panel
NOTE 1:
W1 RS-485
TERMINATION
JUMPER
SHORT J6 TO DISABLE THE KEYPAD.
OPEN J6 TO ENABLE THE KEYPAD.
NON-RESETTABLE 24 VDC POWER IN (+)
24 VDC COMMON IN (-)
NON-RESETTABLE 24 VDC POWER OUT (+)
24 VDC COMMON OUT (-)
EXTRA GROUND
EARTH GROUND
1
1
OVERLAY
SWITCHES
OVERLAY
LEDS
SW1
DBG
ASSY, LCD-SLP
1120-0938 REV ___
KEYSWITCH
J6
1
2
3
4
1
2
3
4
5
6
TB2
DISPLAY
TB1
RS-485
+
ON
OFF
W1
AUX
TERM
J5
LOCAL
HOST
(SEE NOTE 6)
10
9
2
1
1
NOTE 2:
TO J7 OF THE SLP-E3 MAIN BOARD.
IF USED, MAKE NO CONNECTIONS
TO TERMINAL BLOCKS TB1 OR TB2.
RS-485 COM A IN
RS-485 COM B IN
RS-485 COM A OUT
RS-485 COM B OUT
CAUTION!
USE THESE TERMINALS
ONLY WHEN THE LCD-SLP
IS REMOTELY MOUNTED
OR CONMNECTED TO AN
ILI-MB-E3 OR ILI95-MB-E3.
DO NOT USE THESE
TERMINALS WHEN
THE J5 RIBBON CABLE IS
CONNECTED TO J7 OF
THE SLP-E3 MAIN BOARD.
J1 J2
1
TB2
DISPLAY
O
VERLAY
SW
IT
CH
ES
1
O
VER
LAY
LED
S
J1
J2
SW1
DBG
NON-RESETTABLE 24 VDC POWER IN (+) FROM ILI-MB-E3 TB3 TERM 6
24 VDC COMMON IN (-) FROM ILI-MB-E3 TB3 TERM 7
NON-RESETTABLE 24 VDC POWER OUT (+)
24 VDC COMMON OUT (-)
EXTRA GROUND
EARTH GROUND
RS-485 COM A IN FROM ILI-MB-E3 TB3 TERM 1
RS-485 COM A OUT
RS-485 COM B OUT
RS-485 COM B IN FROM ILI-MB-E3 TB3 TERM 2
ASSY, LCD-SLP
1120-0938 REV ___
1
2
3
4
5
6
TB1
RS-485
1
2
3
4
1
SHORT J6 TO DISABLE THE KEYPAD.
OPEN J6 TO ENABLE THE KEYPAD.
NOTE 1:
TO: ASM-16 TB1 TERM 3
ANU-48 TB1 TERM 3
REMOTE LCD-SLP TB2 TERM 1
LCD-E3 TB1 TERM 1
LCD-7100 TB1 TERM 5
NOTE 2:
TO: ASM-16 TB1 TERM 4
ANU-48 TB1 TERM 4
REMOTE LCD-SLP TB2 TERM 2
LCD-E3 TB1 TERM 2
LCD-7100 TB1 TERM 6
NOTE 3:
TO: ASM-16 TB1 TERM 1
ANU-48 TB1 TERM 1
REMOTE LCD-SLP TB1 TERM 1
LCD-E3 TB1 TERM 3
LCD-7100 TB1 TERM 1
NOTE 4:
TO: ASM-16 TB1 TERM 2
ANU-48 TB1 TERM 2
REMOTE LCD-SLP TB1 TERM 2
LCD-E3 TB1 TERM 4
LCD-7100 TB1 TERM 2
+
KEYSWITCH
J6
ON
OFF
W1
AUX
TERM
J5
LOCAL
HOST
(SEE NOTE 6)
NOTE 6:
CONNECTOR J5 NOT USED
WHEN LCD-SLP CONNECTS
TO AN ILI-MB-E3.
DO NOT CONNECT J5 TO
ASM-16, J1, J2, OR J3 OR
TO ANU-48 J1 OR J2.
10
9
2
1
NOTE 1:
W1 RS-485
TERMINATION
JUMPER
