background image

2

ILI-MB-E3 Product Installation Document —

 P/N 9000-0579:M7  07/02/2018

1.1  Mass Notification System (MNS)

The Gamewell-FCI, Mass Notification System (MNS) is a Combination In-Building Fire and Mass Notification System. It 
comprises the E3 Series Broadband Emergency Voice Evacuation and the E3 Series Broadband Networked Fire Alarm Systems. 
This design allows a wide range of configurations to form an integrated, distributed fire alarm system in combination with the audio 
evacuation for both Fire and Mass Notification functions as desired. The design also allows for its use as a dedicated standalone 
Mass Notification System without the fire alarm service. The network communication conveys all Fire Alarm and Mass 
Notification control functions, audio evacuation, voice paging, and fire fighter communications over a single pair of wires or fiber-
optic cable. The modular design offers several configurations to accommodate the following audio components:

Autonomous Control Unit (ACU), (Main Command Center)

Local Operating Console (LOC), (Remote Command Center)

E3 Series Broadband Voice Evacuation System

Table 1.1.1 lists the E3 Series sub-assemblies that can be used in the Gamewell-FCI, MNS (Mass Notification System).

1.1.1 Mass Notification System - Documentation

The following MNS System information is available in the Gamewell-FCI,

 Mass Notification System (MNS) Installation/Operation 

Manual, Part Number:LS10013-000GF-E

E3 Series

®

 and Velocit

®

 i a registered trademark and CAMWorks™ is a trademark of Honeywell International Inc.

UL

®

 is a registered trademark of Underwriters Laboratories, Inc.

©2018 Copyright by Honeywell International, Inc. All rights reserved.

Autonomous Control Unit (ACU) 

(Main Command Center)

E3 LOC Remote Command Center

E3 Broadband System

(Distributed System)

AM-50 Series Amplifiers

AOM-TELF/AOM-2SF

AM-50 Series Amplifiers

ANU-48 (Remote Annunciator)

ASM-16 (Addressable Switch Module)

ANU-48 (Remote Annunciator)

ASM-16 (Addressable Switch Module)

INI-VG Series
(First/Second/Third Generation)
(Intelligent Network Interface Voice 
Gateway) 

ASM-16 (Addressable Switch Module)

ILI-MB-E3 
(Intelligent Loop Interface-Main Board)

INCC-MIC (Microphone)

ILI-MB-E3 
(Intelligent Loop Interface-Main Board)

ILI-S-E3 (Intelligent Loop Interface-
Expansion Board)

NGA (Network Graphic Annunciator)

ILI-S-E3 (Intelligent Loop Interface-
Expansion Board)

ILI95-MB-E3 
(Intelligent Loop Interface-Main Board)

INCC-TEL (Telephone)

ILI95-MB-E3 
(Intelligent Loop Interface-Main Board)

ILI95-S-E3 (Intelligent Loop Interface95-
Expansion Board)

ILI95-S-E3 (Intelligent Loop Interface95-
Expansion Board)

INCC-MIC (Microphone)

INCC-MIC (Microphone)

INCC-TEL (Telephone)

INCC-TEL (Telephone)

INI-VG Series
(First/Second/Third Generation)
 (Intelligent Network Interface Voice 
Gateway) 

INI-VGC, (First/Second/Third Generation) 
(Intelligent Network Interface Voice 
Gateway)

NGA (Network Graphic Annunciator)

INI-VGX, (First/Second/Third Generation) 
(Intelligent Network Interface Voice 
Gateway)

PM-9/PM-9G (Power Supply)

NGA (Network Graphic Annunciator)

RPT-E3-UTP (Communication Circuit)

PM-9/PM-9G (Power Supply)

RPT-E3-UTP (Communication Circuit)

NOTE 1: 

In the E3 Series, Mass Notification System, the LCD-E3 and LCD-SLP Display panels are not used.

Table 1.1.1 E3 Series Modules Used in the MNS System

System Configurations  

Class 2 Power-Limited Requirements     

System Operation

Cabinets Installations

Wiring

Testing/Maintenance   

Summary of Contents for Gamewell FCI ILI-MB-E3



















Reviews: