Honeywell G Installation Instructions Manual Download Page 5

T7047C,G,H REMOTE SPACE SENSORS

5

62-0179

Fig. 12. T7047C1025 used as a remote 

sensor with T7067B Thermostat.

Fig. 13. Four T7047C1025 Sensors providing 

a temperature-averaging network for a 

T7300/Q7300 Thermostat/Subbase.

Fig. 14. Two T7047G1000 Sensors providing a 

temperature-averaging network for a 

T7300/Q7300 Thermostat/Subbase.

Fig. 15. Five T7047G1000 Sensors providing 

a temperature-averaging network for a 

T7300/Q7300 Thermostat/Subbase.

Fig. 16. Nine T7047C1025 Sensors providing 

a temperature-averaging network for a 

T7300/Q7300 Thermostat/Subbase.

T T1 3

4

2

5

1 T R T R W B

Y R

S

EN

S

OR

STAT

24

 VAC

ECONO

1

POWER SUPPLY.  PROVIDE DISCONNECT MEANS AND OVERLOAD 
PROTECTION AS REQUIRED.

TERMINAL 8 IS USED WITH THE W974A, B ONLY.  TERMINAL 6 IS
USED WITH THE W974A, B AND/OR REMOTE SENSING ELEMENT 
(T7067B ONLY).

TERMINALS 6 AND 7 ARE USED TO CONNECT THE REMOTE SENSING 
ELEMENT TO THE T7067B ONLY.  NO SCREW IS PROVIDED WITH THE 
T7067A FOR TERMINAL 7.  DOTTED LINES SHOW REMOTE SENSING 
ELEMENT CONNECTIONS.

2

C7046A 
DISCHARGE
AIR SENSOR

L1 
(HOT)

L2

M3411

W973 LOGIC PANEL

3

1

C   +20   H   N

3

2

2

3

4

2

5

6

7

1

8

T

T

T7067 WALLPLATE

T7047C
REMOTE
SENSOR

M3420

T

T

T

T

Q7300

T7047C

T

T

T7047C

T

T

T7047C

T

T

T7047C

M3421

T

T

Q7300

T

T

T7047G1000

T7047G1000

T

T

M3422

T

T

Q7300

T

T

T7047G

T

T

T7047G

T

T

T7047G

T

T

T7047G

T

T

T7047G

M3419

T

T

T

T

Q7300

T7047C

T

T

T7047C

T

T

T7047C

T

T

T7047C

T

T

T7047C

T

T

T7047C

T

T

T7047C

T

T

T7047C

T

T

T7047C

Summary of Contents for G









Reviews: