background image

® U.S. Registered Trademark
Copyright © 2001 Honeywell • All Rights Reserved 

INSTALLATION INSTRUCTIONS

62-0179

T7047C,G,H

Remote Space Sensors

APPLICATION

The T7047 Remote Space Sensors are used in Series 70 

Control Systems to provide modulating space 
temperature control.

SPECIFICATIONS

IMPORTANT

The specifications given in this publication do 
not include normal manufacturing tolerances. 

Therefore, this unit may not exactly match the 
listed specifications. This product is tested and 

calibrated under closely controlled conditions, 
and some minor differences in performance can 

be expected if those conditions are changed.

Models:

T7047C: 2-wire remote sensor with no internal 

adjustment means (requires remote setpoint device 
such as S963B, T7067B, and T7080B).

T7047C1009: 2-wire remote sensor for use with 

control systems such as M7044 and M7045 

Motors.

T7047C1025: 2-wire remote sensor for use with control 

systems such as the W927, W960, and W973.

T7047C1082: 2-wire remote sensor for use with 

T7080B Transmitter in W7080 Multizone Control 
System.

T7047G: 2-wire remote sensor with no internal 

adjustment means (requires remote setpoint device 

such as S963B, T7067B or T7080B).

T7047H: Thin-film, platinum 1K (at 0°C) temperature 

sensor only. For use with the Excel 80/100/500/600 
Controllers.

Dimensions: 

See Fig. 1.

Mounting: 

Mounts on wall or 2 x 4 in. vertical outlet box 

with screws provided.

Temperature Sensor: 

Thermistor-resistor element.

Cover Thermometer (available on most models):

Element: Bimetal.

Range: 55 to 95°F (13 to 35°C).

Summary of Contents for G









Reviews:

Related manuals for G