background image

Europe

The CE marking on the product indicates that this device is in confor-

mity with all essential requirements of the 1999/5/EC R&TTE Direc-

tive and 2011/65/EU RoHS directive. In addition, complies to 2006/

95/EC Low Voltage Directive, when shipped with recommended 

power supply.

 

European contact:

Hand Held Products Europe B.V.

 

Nijverheidsweg 9-13

 

5627 BT Eindhoven

 

The Netherlands
Honeywell shall not be liable for use of our product with equipment 

(i.e., power supplies, personal computers, etc.) that is not CE marked and does 

not comply with the Low Voltage Directive. 

Honeywell Scanning & Mobility Product Environmental 
Information

Refer to 

www.honeywellaidc.com/environmental

 for the RoHS / REACH / 

WEEE information.

Product Agency Compliance - AP-010BT

 Class II

Brazil

Product Agency Compliance - AP-100BT

 Class I

Patents

For patent information, please refer to 

www.hsmpats.com

.

Modelo: AP-010BT

0921-11-6583

(01)07898927490089

" Este equipamento opera em caráter secundário, isto é, não tem 
direito a proteção contra interferência prejudicial, mesmo de estações 
do mesmo tipo, e não pode causar interferência a sistemas operando 
em caráter primário."

Summary of Contents for FocusBT AP-010-BT















Reviews: