manualshive.com logo in svg

Honeywell Fire Sentry SS4-AUV, Installation Manual And Operating Manual, Page: 17 / 20

Share
Download
Honeywell Fire Sentry SS4-AUV Installation Manual And Operating Manual Download Page 17

Model SS4-AUV/-AUV2 Ultraviolet (UV) Digital Electro-Optical Fire Detector

 

Installation Guide and Operating Manual 
MAN0927_V3_1510-005_Rev H_06-13

 

 

 

15 

 

 

TABLE 2:  Configuration DIP Switch Settings 

Verification Time 

DIP SWITCH

 

1 

DIP SWITCH

 

2 

DIP SWITCH

 

3 

          DESCRIPTION 

closed 

closed 

closed 

Verify is disabled and the Verify Relay is unused.

   Factory setting

 

closed 

open 

open 

Verify is enabled and the Verify time is 5 seconds. 

open 

closed 

open 

Verify is enabled and the Verify time is 10 seconds. 

closed 

closed 

open 

Verify is enabled and the Verify time is 15 seconds. 

open 

open 

closed 

Verify is enabled and the Verify time is 20 seconds. 

closed 

open 

closed 

Verify is enabled and the Verify time is 25 seconds. 

open 

closed 

closed 

Verify is enabled and the Verify time is 30 seconds. 

open 

open 

open 

Verify is disabled and the Verify Relay operates as a second Fire Relay. 

Latching 

DIP SWITCH

 

4 

          DESCRIPTION 

open 

Non-Latching mode.  If Verify is enabled then the Verify Relay will de-energize approximately 10 
seconds after it energizes.  If Verify is disabled then the Fire Relay(s) will de-energize 
approximately 10 seconds after it energizes.  

The SS4-AUV2 Factory setting is Non-Latching

 

closed 

Latching mode.  If Verify is enabled then when the Verify Relay energizes it will remain 
energized until the Detector is reset.  If Verify is disabled then when the Fire Relay energizes it 
will remain energized until the Detector is reset. 

 The SS4-AUV Factory setting is Latching

 

 

DIP SWITCH

 

5 

          DESCRIPTION 

N/A 

 DIP SWITCH 5 is not used in the SS4-AUV/-AUV2 

Test Cycle 

DIP SWITCH

 

6 

          DESCRIPTION 

open 

Testing of the Lens occurs every 30 minutes. 

 Factory setting

 

closed 

* Testing of the Lens occurs every 6 minutes 

* Utilization of the 6-minute period may adversely affect the source tube service life. 

Fire Range 

DIP SWITCH

 

7 

DIP SWITCH

 

8 

          DESCRIPTION 

open 

open 

Set to detect an industry standard 1 sq. ft.  fire at 15 ft. on axis. 

closed 

open 

Set to detect an industry standard 1 sq. ft.  fire at 30 ft. on axis. 

open 

closed 

Set to detect an industry standard 1 sq. ft.  fire at 45 ft. on axis. 

Factory setting

 

closed 

closed 

Set to detect an industry standard 1 sq. ft.  fire at 60 ft. on axis. 

 

 

 

 

 

 

Summary of Contents for Fire Sentry SS4-AUV





















Reviews:

No comments