Honeywell Fire-Lite Alarms ECC-125DA Installation Manual Download

Page: 35 / 38

ECC-50/125DA Instruction Manual —

P/N LS10027-000FL-E:D 5/21/2015

Installation

ECC-50BDA Backup Remote Amplifier

The AC terminals are rated as 120 VAC, 60 Hz or 240 VAC, 50 Hz.

3.2.10 Backup Battery for ECC-50BDA

The following steps explain how to connect the batteries (refer to Figure 3.12):

1. Connect the black wire of the battery harness to the (-) side of the battery #2.
2. Connect the jumper wire provided form the positive (+) side of battery #2 to the negative (-)

side of battery #1.

3. Connect the red wire from the battery harness to the positive (+) side of battery #1.

Figure 3.11 AC Connection

white

green

black

c.w

+ -

+ - + - + - + -

OUT

TB6

TB5

TB2

Figure 3.12 Battery Connection to ECC-50BDA

Note:

Batteries have been

rotated to show the tops for
illustration purposes only.

50d

bat

t.w

firealarmresources.com

Summary of Contents for Fire-Lite Alarms ECC-125DA







































Search results

Summary of Contents for Fire-Lite Alarms ECC-125DA

Reviews:

Related manuals for Fire-Lite Alarms ECC-125DA

Brands by name

Popular brands

Honeywell Fire-Lite Alarms ECC-125DA, Installation Manual

Search results

Summary of Contents for Fire-Lite Alarms ECC-125DA

Reviews:

Related manuals for Fire-Lite Alarms ECC-125DA

Brands by name

Popular brands