Honeywell ExiLED Series Manual Download Page 2

Page 

2

 of 

8

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

 
 
 
The ExiLED is a self-contained LED exit sign with selftest function. It can be configured as maintained 
or non-maintained. 
 

Selftest functions 
 

Every 15 days the luminaire will perform an emergency operation test, this will light the exit sign for 
approx. 3 seconds. The red indicator LED will flash during this test sequence. 
 
Every 6. month the luminaire will perform a battery condition test. The test will last for 60 minutes. The 
exit sign will be lit and the yellow indicator LED will flash during this test sequence. 
 

Manual test functions 
 

Manual tests can only be performed if both mains and battery are connected. 
 
By pressing the test button briefly (less than 5 seconds) an emergency operation test is performed. 
The exit sign will be lit for approx. 3 seconds, the red indicator LED will flash during this test sequence. 
 
By pressing the test button for between 5 and 10 seconds a battery condition test is performed. 
This test will last for 60 minutes and can only be performed when the battery is fully charged (steady 
green indicator LED). The exit sign will be lit and the yellow indicator LED will flash during this test 
sequence. 
 

Resetting errors 
 

Push the test button for >10 seconds to delete all indicated errors. Then the luminaire enters regular 
operation mode. 
  

Dimming 

 
By pressing the test button continuously for 15 seconds, when luminaire is connected to mains, the 
luminosity will be reduced to 10% of its total luminance. In emergency mode the light output will 
remain unchanged. 
To restore the original settings, repeat the above procedure. 
The dimming setting remains stored in the luminaire even when both mains and battery voltages are 
disconnected.

ExiLED22   ExiLED34   ExiLED44 

 

Lumen output, normal:   

105 lm 

125 lm        145 lm 

Lumen output, emergency: 

130 lm         155 lm        180 lm 

Weight: 

 

 

540g 

690g           820g 

Maximum power consumption:  

8VA             9VA            9VA 

Operation voltage:  

 

220-240VAC 50/60Hz 

Emergency mode duration: 

Minimum 1 hour 

Battery: 

 

 

3,6V / 1,2Ah NiMH 

Battery protection: 

 

Overcharge and full discharge 

Charging time:  

 

13 hours 

Ambient temperature range:  

5 to 40°C 

Relative humidity: 

 

Up to 95% 

Classification: 

 

EN 60598-2-22 

IP40 

Expected battery lifetime 4 years 

Indicator LEDs 

GB 

GREEN

 

 

YEL

LO

W

 

 

RED

 

 

Normal 

Charging (battery test not possible while charging) 

Mains off, battery not connected or charger fault 

Battery test 

Battery fault 

Light source test 

Light source fault 

Battery fault and light source fault 

 

Description 

LED status explanation 

Off 

 

On 

 

Flashing 

 

Technical description 

At the end of their useful life the 
packaging, product and batteries 
should be disposed of via a 
suitable recycling centre. Do not 
dispose of with your normal 
household waste. Do not burn. 

T45807-B4-4 

Summary of Contents for ExiLED Series









Reviews: