background image

PRODUCT SPECIFICATIONS

Range:

15 m x 18 m  (50' x 60')

Alarm relay (DT-7450):

Energized Form A
125 mA, 25 VDC, 20 Ohm series resistor

Alarm relay (DT-7450C):

Energized Form C
125 mA, 25 VDC, 20 Ohm series resistor

Tamper switch:

(NC)  50 mA, 24 VDC

Power requirements:

7.5 - 16 VDC (for UL 8.0 - 16 VDC)
DT-7450 -- 25 mA typical, 30 mA maximum, 12 VDC
DT-7450C -- 30 mA typical, 35 mA maximum, 12 VDC
AC Ripple: 3 V peak-to-peak at nominal 12 VDC

Microwave frequencies:

24.125 GHz

PIR white light immunity:

6,500 Lux typical

Fluorescent light filter:

50 Hz or 60 Hz selectable

RFI immunity:

30 V/m,10 MHz - 1000 MHz

Operating temperature:

14

F to +131

F  (-10

C to +55

o

 C)

5 - 95% relative humidity (non-condensing)

Temperature compensation:

Advanced Dual Slope

Self-test intervals:

Microwave Supervision
PIR self-test
Temp. Comp.

PIR fields-of-view:

Standard Wide Angle Lens
22 long range edges
12 intermediate edges
6 lower edges
4 Look-down edges

Dimensions:

11.9 cm H x 7.1 cm W x 4.2 cm D
(4.685" H x 2.795" W x 1.654" D)

Sensitivity:

Low (Pulse count 2) 3 - 4 steps
High (Pulse count 1) 2 - 3 steps

Accessories:

Optional Lens Kit -- Curtain Lens Kit (P/N DT7000-LRLK)
SMB-10 Swivel Mount Bracket (P/N 0-000-110-01)
SMB-10C Swivel Mount Ceiling Bracket  (P/N 0-000-111-01)
SMB-10T Swivel Mount Bracket w/ Tamper (P/N 0-000-155-01)

Approvals/listings:

FCC
IC
cULus

© 2001 Honeywell

 

International Inc.  • Honeywell, IntelliSense and DUAL TEC are registered trademarks of Honeywell International Inc.

All other trademarks are the properties of their respective owners. All rights reserved.

5-051-640-00  Rev  E

LED INDICATORS

DIP SWITCH SETTINGS (SW1)

Factory default settings are shown in grey.

DETECTION PATTERNS

DT

-7450/7450C DU

AL TEC

®

 Motion Sensor Product Information

40' 50'

30'

20'

10'

0

0

15 m

40'

12 m

12 m

12 m

40'

30'

9 m

9 m

9 m

30'

20'

6 m

6 m

6 m

20'

10'

3 m

3 m

3 m

10'

0

0

floor

long range

intermediate

lower

down

Zones

50'

40'

30'

20'

10'

0

2.3 m (7'6")

3 m

6 m

9 m

12 m 15 m

DT-7450/7450C Side View

Wide Angle Lens

TROUBLE SHOOTING
Problem: 

 Red LED is flashing rapidly.

Explanation: 

 The sensor is in one of three conditions:

Microwave supervision failure:  The sensor continues operating

using PIR as the only detection method. When detection occurs

on the PIR channel, the alarm relay will latch open until the

Microwave trouble is removed.
PIR self-test failure:  Alarm relay does not actuate.
Temperature compensation failure:  When alarm occurs, the

alarm relay will latch open until the trouble is cleared.

Solution:

  Power down the sensor or enter the zone finder mode

which will perform self-test. If the trouble does not clear, replace

the sensor.

LED

Red

Yellow

Green

Normal

ON

Alarm

ON

Microwave

ON
PIR

Power Up

Slow
Blink

OFF

OFF

Trouble

Fast

Blink

OFF

OFF

Zone Finder

OFF

ON

Microwave

ON
PIR

OPERATION MODE

DT-7450/7450C Top View

Wall Mounted Wide Angle Lens with Typical Alarm Pattern

FCC Notice

: This equipment has been tested and found to comply with the limits for

a field disturbance sensor pursuant to Part 15 of the FCC Rules.  The user is

cautioned that changes or modifications not expressly approved by Honeywell could

void the user’s authority to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications.  However, there is no guarantee that

interference will not occur in a particular installation.  If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

S

witch

1

2
3

OFF

Low Sensitivity

(Pulse Count 2)

LED Disabled

60 Hz Fluorescent Filter

ON

High Sensitivity
(Pulse Count 1)

LED Enabled

50 Hz Fluorescent Filter

Reviews: