Honeywell Dolphin 7600 Installation And User Manual Download Page 31 | Manualshive

Page: 31 / 64

background image

27

Changing the Beeper Tone & Volume

Changing the Beeper Tone

Beeper tones may be programmed directly or incrementally using the following
bar code. The new tone will be heard followed by a short pause. Two more new
tones will be heard signifying the new setting has been stored in memory. The
silent (no beep) tone is also selectable.

³

9

9

9

9

7

5

N

Changing the Beeper Volume

Volume levels may be programmed directly or incrementally using the following
bar code. The new volume will be heard followed by a short pause. Two more
tones will be heard signifying the new setting has been saved in memory. The
silent (no volume) tone is also selectable.

³

9

9

9

9

7

4

N

These volume control and beeper tone bar codes can also be found under the
Top plate of the scanner and in the MetroSelect Programming Guide.

Figure 27: Additional Beeper Tone and Volume Control Bar Codes

«
...
29
30
31
32
33
...
»

Summary of Contents for Dolphin 7600

































































Reviews:

No comments

Related manuals for Dolphin 7600

Brand: Youjie Pages: 52

Brand: Banner Pages: 4

ABR 3000 series

Brand: Banner Pages: 8

Brand: Hamlet Pages: 58

Brand: ICT Pages: 38

Brand: Ectaco Pages: 11

Brand: American Dynamics Pages: 20

Brand: Argox Pages: 159

Brand: extronics Pages: 27

Brand: Scantech Pages: 86

Brand: iMotion Pages: 61

Brand: Rosslare Pages: 25

Brand: Di-soric Pages: 174

Brand: TAGSYS RFID Pages: 48

Lector62 Series

Brand: SICK Pages: 131

Brand: Avery Dennison Pages: 26

Brand: Worth Data Pages: 39

Brand: Datalogic Pages: 428

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands